Arsenic contamination of groundwater is a serious concern worldwide. The research gaps in removing arsenic are selectivity, regeneration and effective removal rate at neutral pH levels. In this study, we discussed the reasons of the high arsenic adsorption from groundwater of our previously developed adsorbent, a cationic polymer gel, N,N-dimethylamino propylacrylamide, methyl chloride quaternary (DMAPAAQ), loaded with iron hydroxide. We used a transmission electron microscope (TEM) and thermogravimetric analyser (TGA) to detect the iron contents in the gel and ensure its maximum impregnation. We found that the gel contains 62.05% FeOOH components. In addition, we used the Mössbauer spectroscopy to examine the type of impregnated iron in the gel composite and found that it was γ-FeOOH. Finally, we used Fourier transform infrared spectroscopy (FTIR) to examine the surface functional groups present in the gel and the differences in those groups before and after iron impregnation. Similarly, we also investigated the differences of the surface functional groups in the gel, before and after the adsorption of both forms of arsenic. To summarize, this study described the characteristics of the gel composite, which is selective in adsorption and cost effective, however further applications should be investigated.
The groundwater in approximately 50% of the Bangladesh landmass contains Mn concentrations greater than the limit prescribed by the WHO drinking water guidelines. Although studies have suggested that γ-FeOOH can effectively remove Mn from water, its practicability has not been investigated, considering that the additional processes required to separate the adsorbents and precipitates are not environment-friendly. To improve the efficiency of adsorptive Mn-removal under natural conditions, we employed a cationic polymer gel composite, N,N’-Dimethylaminopropyl acrylamide, methyl chloride quaternary (DMAPAAQ) loaded with iron hydroxide (DMAPAAQ + FeOOH), and a non-ionic polymer gel composite, N,N’-Dimethylacrylamide (DMAA) loaded with iron hydroxide (DMAA + FeOOH). DMAPAAQ + FeOOH exhibited a higher As removal efficiency under natural conditions while being environment-friendly. Our results suggest that the higher efficiency of the cationic gel composite is owed to the higher γ-FeOOH content in its gel structure. The maximum adsorption of Mn by DMAPAAQ + FeOOH was 39.02 mg/g. Furthermore, the presence of As did not influence the adsorption of Mn on the DMAPAAQ + FeOOH gel composite and vice versa. DMAPAAQ adsorbed As and the γ-FeOOH particles simultaneously adsorbed Mn. Our findings can serve as a basis for the simultaneous removal of contaminants such as As, Mn, Cr, and Cd.
To probe the effects of pendant side-chain structures on the properties of porous thermoresponsive polymer gels, oligo(ethylene glycol) alkyl ether acrylates were polymerised in an aqueous medium under radical-mediated phase-separation conditions. The monomer structures varied according to the lengths and termini of their ethylene glycol side chains. The porous poly(oligo(ethylene glycol) alkyl ether acrylate) (POEGA) gels exhibited variable lower critical solution temperatures (LCSTs) but similar and rapid swelling–deswelling behaviours. Although the LCST of the poly(tri(ethylene glycol) monomethyl ether acrylate) (PTEGA) gel decreased with increasing aqueous NaCl or CaCl2 concentration, PTEGA showed excellent thermosensitivity in highly concentrated salt solutions, recommending its application in saline environments. Examination of PTEGA adsorption performance in an oil–water emulsion showed that n-tridecane adsorption increased with temperature. Although n-tridecane was effectively adsorbed at 70 °C, its release from the fully adsorbed PTEGA gel was difficult despite a temperature reduction from 70 to 20 °C.
In this work, we prepared an adsorbent composed of a cationic polymer gel containing iron hydroxide in its structure designed to adsorb arsenic from groundwater. The gel we selected was the N,N-dimethylamino propylacrylamide methyl chloride quaternary (DMAPAAQ) gel. The objective of our preparation method was to ensure the maximum content of iron hydroxide in the structure of the gel. This design approach enabled simultaneous adsorption by both the polymer structure of the gel and the iron hydroxide component, thus, enhancing the adsorption capacity of the material. To examine the performance of the gel, we measured reaction kinetics, carried out pH sensitivity and selectivity analyses, monitored arsenic adsorption performance, and conducted regeneration experiments. We determined that the gel undergoes a chemisorption process and reaches equilibrium at 10 h. Moreover, the gel adsorbed arsenic effectively at neutral pH levels and selectively in complex ion environments, achieving a maximum adsorption volume of 1.63 mM/g. The gel could be regenerated with 87.6% efficiency and NaCl could be used for desorption instead of harmful NaOH. Taken together, the presented gel-based design method is an effective approach for constructing high-performance arsenic adsorbents.
A thermosensitive gel that exhibits lower critical solution temperature (LCST) becomes hydrophilic at low temperatures and hydrophobic at high temperatures in water. A system for absorbing hydrophobic organic matters that exploits this property has been reported. While washing the gel at a low temperature with a good solvent is a possible method for removing the adsorbed matter, a process that then shrinks the gel is also required. Herein, we focused on poly[oligo(ethylene glycol) mono(m)ethyl ether acrylate] (POEGA) gels as thermosensitive gels suitable for use in this system. POEGAs are known to contain poly(ethylene glycol) (PEG) units in their side chains and exhibit upper critical solution temperature (UCST) behavior in aliphatic alcohols. By exploiting this property, we developed a method for removing hydrophobic matters that accumulate in these gels; we also evaluated the LCST and UCST behavior of POEGA gels in alcohol–water mixtures, and measured the LCSTs of these gels in water and their UCSTs in some alcohols.