Deepak Verma

Dr. Deepak Verma

Birla Institute of Technology, Mesra, Rānchi, Jharkhand, International

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2016 in Renewable and Sustainable Energy Reviews
Verified
Journal Article
Closed access
DVDeepak Verma
Deepak Verma
SNSavita Nema
Savita Nema
ASA.M. Shandilya
A.M. Shandilya
SDSoubhagya K. Dash
Soubhagya K. Dash

1 October 2017 in Renewable and Sustainable Energy Reviews
Verified
Journal Article
Closed access
SDSoubhagya K. Das
Soubhagya K. Das
DVDeepak Verma
Deepak Verma
SNSavita Nema
Savita Nema
RNR.K. Nema
R.K. Nema

1 January 2016
Verified
Conference Paper
Closed access
PSPooja Sahu
Pooja Sahu
DVDeepak Verma
Deepak Verma
SNS Nema
S Nema
Renewable energy is an alternative way that will hopefully lead us away from petroleum dependent energy sources. Among all renewable energy sources solar energy is the most acceptable solution as it is available in abundant and free of cost worldwide. A typical solar generation system consists of a solar array and a DC-DC converter. A DC-DC converter acts as an interface between the load and the PV module as it serves the purpose of transferring maximum power from the solar PV module to the load. To develop a photovoltaic (PV) power generation system with a suitable converter topology, it is imperative to analyze the converter. In this paper modeling and physical design of DC-DC boost converter is presented for solar PV system (TET-1210 made by Thrive Energy Technologies Pvt. Ltd.) and tested in SIMSCAPE library of MATLAB. The result shows that the designed converter can be implemented with any maximum power point tracking technique and gives the maximum power at 70.06% of duty cycle. The small signal analysis of boost converter is also given in this paper which is very helpful for the stability analysis.

13 April 2020 in International Transactions on Electrical Energy Systems
Verified
Journal Article
Closed access
PDF file
NKNikhil Kumar
Nikhil Kumar
SNSavita Nema
Savita Nema
RNRajesh K. Nema
Rajesh K. Nema
DVDeepak Verma
Deepak Verma

27 March 2022 in Electronics
Verified
Journal Article
Open access
PDF file
DVDeepak Verma
Deepak Verma
SNSavita Nema
Savita Nema
Rakeshwri AgrawalRakeshwri Agrawal
Rakeshwri Agrawal
Yashwant SawleYashwant Sawle
Yashwant Sawle
AKAlok Kumar
Alok Kumar
This paper presents a maximum power point tracking (MPPT) algorithm in a solar photovoltaic (SPV) system that requires fewer sensors, is easy to implement, and offers a good tracking efficiency and speed. Among various MPPT algorithms found in literature, the perturb and observe (P&O) algorithm is most popular as it required less complex circuitry and is easy to implement, but it suffers against fast-changing environmental conditions mostly in the case of partial shading conditions and requires two sensors, i.e., voltage and current. This paper presents the one sensor-based method based on the modified converter design which eliminates the effect of partial shading conditions as well as the fast-changing environmental condition. The presented MPPT algorithm was implemented and tested using an FPGA-based NI-sbRIO card interfaced with Labview software.

1 November 2015 in Journal of Renewable and Sustainable Energy
Verified
Journal Article
Closed access
SDSoubhagya Kumar Dash
Soubhagya Kumar Dash
SNSavita Nema
Savita Nema
RNR. K. Nema
R. K. Nema
DVDeepak Verma
Deepak Verma
Under shading condition, the power–voltage characteristics of the photovoltaic (PV) modules exhibit complexity with multiple numbers of peaks. Existence of multiple peaks leads to additional difficulties in tracking maximum power point (MPP) and shall mar efficiency of PV arrays under shading, if appropriate measures are not taken. It is due to the nonlinear characteristics of PV cell, maximum power can be extracted under particular weather condition. Maximum power point tracking (MPPT) techniques are used to maximize PV array output power continuously, by tracking MPP, the location of which depends on atmospheric temperature and solar insolation. The major drawbacks of traditional MPPT techniques are that they are unable to track global peak under non-uniform irradiance/insolation. Numerous techniques are reported in literature to find MPP in both under uniform insolation and partial shading condition. This paper presents a comprehensive review of various MPPT techniques under uniform and non-uniform irradiances and comparatively evaluates them for their merits and demerits. The review is helpful in selecting appropriate MPPT techniques and adjudges its impact on the given solar PV applications.