Air-quality measurements in a deep underground mine are a critical issue. The cost of ventilation, as well as the geometry of the considered mine, make this process very difficult, and local air quality may be a danger to miners. Thus, portable, personal devices are required to inform miners about gas hazards. There are available tools for that purpose; however, they do not allow the storage of data collected during a shift. Moreover, they do not allow the basic analysis of the acquired data cost-effectively. This paper aims to present a system using low-cost gas sensors and microcontrollers, and takes advantage of commonly used smartphones as a computing and visualization resource. Finally, we demonstrate monitoring system results from a test in an underground mine located in Poland.

Belt conveyors are commonly used for the transportation of bulk materials. The most characteristic design feature is the fact that thousands of idlers are supporting the moving belt. One of the critical elements of the idler is the rolling element bearing, which requires monitoring and diagnostics to prevent potential failure. Due to the number of idlers to be monitored, the size of the conveyor, and the risk of accident when dealing with rotating elements and moving belts, monitoring of all idlers (i.e., using vibration sensors) is impractical regarding scale and connectivity. Hence, an inspection robot is proposed to capture acoustic signals instead of vibrations commonly used in condition monitoring. Then, signal processing techniques are used for signal pre-processing and analysis to check the condition of the idler. It has been found that even if the damage signature is identifiable in the captured signal, it is hard to automatically detect the fault in some cases due to sound disturbances caused by contact of the belt joint and idler coating. Classical techniques based on impulsiveness may fail in such a case, moreover, they indicate damage even if idlers are in good condition. The application of the inspection robot can “replace” the classical measurement done by maintenance staff, which can improve the safety during the inspection. In this paper, the authors show that damage detection in bearings installed in belt conveyor idlers using acoustic signals is possible, even in the presence of a significant amount of background noise. Influence of the sound disturbance due to the belt joint can be minimized by appropriate signal processing methods.

The monitoring of drilling processes is a well-known topic in the mining industry. It is widely used for rock mass characterization, bit wear monitoring and drilling process assessment. However on-board monitoring systems used for this purpose are installed only on a limited number of machines, and breakdowns are possible. There is a need for a data acquisition system that can be used on different drilling rigs and for an automatic data analysis procedure. In this paper, we focused on the automatic detection of drilling cycles, presenting a simple yet reliable system to be universally installed on drilling rigs. The proposed solution covers hardware and software. It is based on the measurement of electric current and acoustic signals. The signal processing methods include threshold-based segmentation, a short-time envelope spectrum and a spectrum for the representation of results. The results of the research have been verified on a real drilling rig within the testing site of its manufacturer by comparing the results with the data of the on-board monitoring system installed on the machine. Novel aspects of our approach include the detection of the pre-boring stage, which has an intermediate amplitude that masks the real drilling cycles, and the use of the percussion instantaneous frequency, which is estimated by acoustic recordings.

Locating an inspection robot is an essential task for inspection missions and spatial data acquisition. Giving a spatial reference to measurements, especially those concerning environmental parameters, e.g., gas concentrations may make them more valuable by enabling more insightful analyses. Thus, an accurate estimation of sensor position and orientation is a significant topic in mobile measurement systems used in robotics, remote sensing, or autonomous vehicles. Those systems often work in urban or underground conditions, which are lowering or disabling the possibility of using Global Navigation Satellite Systems (GNSS) for this purpose. Alternative solutions vary significantly in sensor configuration requirements, positioning accuracy, and computational complexity. The selection of the optimal solution is difficult. The focus here is put on the assessment, using the criterion of the positioning accuracy of the mobile robot with no use of GNSS signals. Automated geodetic surveying equipment is utilized for acquiring precise ground truth data of the robot’s movement. The results obtained, with the use of several methods, compared: Wheel odometry, inertial measurement-based dead-reckoning, visual odometry, and trilateration of ultra-wideband signals. The suitability, pros, and cons of each method are discussed in the context of their application in autonomous robotic systems, operating in an underground mine environment.

The rising automation level and development of the Industry 4.0 concept in the mining sector increase the risk of cyber-attacks. As a result, this article focuses on developing a risk analysis method that integrates Kaplan’s and Garrick’s approach and fuzzy theory. The proposed approach takes into account the level of automation of the operating mining processes. Moreover, it follows five main steps, including identifying the automation level in a selected mine, definition of cyber-attack targets, identification of cyber-attack techniques, definition of cyber-attack consequences, and risk ratio assessment. The proposed risk assessment procedure was performed according to three cyber-attack targets (databases, internal networks, machinery) and seven selected types of cyber-attack techniques. The fuzzy theory is implemented in risk parameter estimation for cyber-attack scenario occurrence in the mining industry. To illustrate the given method’s applicability, seven scenarios for three levels of mine automation are analyzed. The proposed method may be used to reveal the current cybersecurity status of the mine. Moreover, it will be a valuable guide for mines in which automation is planned in the near future.

Mobile mapping technologies, based on techniques such as simultaneous localization and mapping (SLAM) and surface-from-motion (SfM), are being vigorously developed both in the scientific community and in industry. They are crucial concepts for automated 3D surveying and autonomous vehicles. For various applications, rotating multiline scanners, manufactured, for example, by Velodyne and Ouster, are utilized as the main sensor of the mapping hardware system. However, their principle of operation has a substantial drawback, as their scanning pattern creates natural gaps between the scanning lines. In some models, the vertical lidar field of view can also be severely limited. To overcome these issues, more sensors could be employed, which would significantly increase the cost of the mapping system. Instead, some investigators have added a tilting or rotating motor to the lidar. Although the effectiveness of such a solution is usually clearly visible, its impact on the quality of the acquired 3D data has not yet been investigated. This paper presents an adjustable mapping system, which allows for switching between a stable, tilting or fully rotating lidar position. A simple experiment in a building corridor was performed, simulating the conditions of a mobile robot passing through a narrow tunnel: a common setting for applications, such as mining surveying or industrial facility inspection. A SLAM algorithm is utilized to create a coherent 3D point cloud of the mapped corridor for three settings of the sensor movement. The extent of improvement in the 3D data quality when using the tilting and rotating lidar, compared to keeping a stable position, is quantified. Different metrics are proposed to account for different aspects of the 3D data quality, such as completeness, density and geometry coherence. The ability of SLAM algorithms to faithfully represent selected objects appearing in the mapped scene is also examined. The results show that the fully rotating solution is optimal in terms of most of the metrics analyzed. However, the improvement observed from a horizontally mounted sensor to a tilting sensor was the most significant.