We investigate the simultaneous effects of aerosol peak height (APH), aerosol properties, measurement geometry, and other factors on the air mass factor for NO2 retrieval at sites with high NO2 concentration. A comparison of the effects of high and low surface reflectance reveals that NO2 air mass factor (AMF) values over a snowy surface (surface reflectance 0.8) are generally higher than those over a deciduous forest surface (surface reflectance 0.05). Under high aerosol optical depth (AOD) conditions, the aerosol shielding effect over a high-albedo surface is revealed to reduce the path-length of light at the surface, whereas high single scattering albedo (SSA) conditions (e.g., SSA = 0.95) lead to an increase in the aerosol albedo effect, which results in an increased AMF over areas with low surface reflectance. We also conducted an in-depth study of the APH effect on AMF. For an AOD of 0.1 and half width (HW) of 5 km, NO2 AMF decreases by 29% from 1.36 to 0.96 as APH changes from 0 to 2 km. In the case of high-AOD conditions (0.9) and HW of 5 km, the NO2 AMF decreases by 240% from 1.85 to 0.54 as APH changes from 0 to 2 km. The AMF variation due to error in the model input parameters (e.g., AOD, SSA, aerosol shape, and APH) is also examined. When APH is 0 km with an AOD of 0.4, SSA of 0.88, and surface reflectance of 0.05, a 30% error in AOD induces an AMF error of between 4.85% and −3.67%, an SSA error of 0.04 leads to NO2 VCD errors of between 4.46% and −4.77%, and a 30% error in AOD induces an AMF error of between −9.53% and 8.35% with an APH of 3 km. In addition to AOD and SSA, APH is an important factor in calculating AMF, due to the 2 km error in APH under high-SZA conditions, which leads to an NO2 VCD error of over 60%. Aerosol shape is also found to have a measureable effect on AMF under high-AOD and small relative azimuth angle (RAA) conditions. The diurnal effect of the NO2 profile is also examined and discussed.
The relative permeabilities of CO2 and brine are important parameters that account for two-phase flow behavior, CO2 saturation distribution, and injectivity. CO2/brine relative permeability curves from the literature show low endpoint CO2 permeability values and high residual brine saturation values. These are the most distinguishing aspects of the CO2/brine relative permeability from oil/water and gas/oil. In this study, this aspect is investigated experimentally by employing a wide range of CO2 injection flow rates. As a result, all the measurements align with previous studies, having low endpoint relative permeability and high residual brine saturation values. They have obvious relationships with the changes in CO2 flow rates. As the CO2 flow rate increases, the endpoint relative permeability increases, the residual brine saturation decreases, and they converge to specific values. These imply that a high CO2 injection flow rate results in high displacement efficiency, but the improvement in efficiency decreases as the flow rate increases. The reasons are identified with the concept of the viscous and capillary forces, and their significance in the CO2 injection into a reservoir is analyzed.
The coalbed methane (CBM) reservoir in Barito Basin, Indonesia may be stimulated by hydraulic fracturing to efficiently recover methane gas from low permeability reservoirs. The permeability of coalbed may be quite diverse, ranging up to a few thousand mD. If the reservoir permeability is too low (less than a tenth md), hydraulic fracturing could be considered to improve gas productivity as a stimulation treatment method. In this study, hydraulic fracturing treatment design is conducted to determine total slurry volume and proper pump rate upon different fracture lengths. To set an optimal treatment schedule, fracture geometry and fracture efficiency were compared depending on the increase of fracture length and pump rate by fracturing stages. The proper pump rate was determined to be 40 bpm and resulting from high fracture efficiency. Furthermore, usage of proppant was determined using definite proper pump rate and slurry volume determined by highest pump rate in this study. All calculated fracture lengths of treatment with proppant were shorter than the fracture length of treatment without proppant. Also, fracture widths and heights were larger than treatment without proppant. However, the fracture efficiency in treatment with proppant was higher than in treatment without proppant. Therefore, proppant would contribute to improving the fracture efficiency of hydraulic fracture treatment in the CBM reservoir in Barito Basin. Consequently, the 3D-propped fracture model was designed for the CBM. Developed hydraulic fracturing model would be useful for the hydraulic treatment of CBM especially in Barito Basin for fracture design and treatment analysis prior to the actual treatment.
The rates and magnitudes of fracture permeability on commercially available proppants were determined from flow through experiments at different stresses and temperatures for hydraulically open and closed systems. A pressure solution model describing multi-mineral dissolution behavior is extended to accommodate the specific nature of the compaction of the synthesized proppant with different chemical compositions. Mechanisms include multi-mineral dissolution, transport, and re-precipitation at the contacting asperities and the free walls within the fractures, resulting in a loss of porosity in proppant packs. The mechanistic model used recovered thermodynamic and kinetic data for mineralogical composition of available proppants within rigid-walled fluid pressure only furnace and ambient stress quadcell reactors. Under reservoir temperature of 191°C and stresses of 65.5 MPa, these ensemble data suggest that proppant packs may compact by up to 10% over the period of a few years.
This study conducted core sampling of an offshore borehole for geological reservoir characterization of a potential CO2 storage site in southeast Korea. From this, two promising geological formations at ~739 and ~779 m were identified as prospective CO2 storage reservoirs. Injection efficiency and CO2 migration were evaluated based on directional measurements of permeabilities from core plugs. The directional transport properties were determined using both a portable probe permeameter and a pressure cell capable of applying different in situ confining pressures. Both steady state and unsteady state measurements were used to determine permeability—the method selected according to the expected permeability range of the specific sample. This expected range was based on rapid screening measurements acquired using a portable probe permeameter (PPP). Anticipated performance of the prototypical CO2 injection site was evaluated based on flow modeling of the CO2 plume migration pathway including CO2 transport through the overlying formations based on the measured directional hydraulic properties. These analyses revealed that the injection efficiency at a depth of 739 m was double that at 779 m. These correlations among and distributions of the directional permeabilities of the potential CO2 geological storage site can be utilized for the assessment of CO2 storage capacity, injectivity, and leakage risk.