Dídia Isabel Cameira Covas

Prof. Dídia Isabel Cameira Covas

DECivil, Instituto Superior Técnico, Lisbon, Lisboa, Portugal
orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2005 in Journal of Hydraulic Research
Verified
Journal Article
Closed access
DCDídia Isabel Cameira Covas
Dídia Isabel Cameira Covas
ISIvaN. Stoianov
IvaN. Stoianov
JMJoão Mano
João Mano
HRHelena Ramos
Helena Ramos
NGNigel Graham
Nigel Graham
CMCedo Maksimovic
Cedo Maksimovic
(2005). The dynamic effect of pipe-wall viscoelasticity in hydraulic transients. Part II—model development, calibration and verification. Journal of Hydraulic Research: Vol. 43, No. 1, pp. 56-70.

1 March 2010 in Journal of Water Resources Planning and Management
Verified
Journal Article
Closed access
DCDídia Isabel Cameira Covas
Dídia Isabel Cameira Covas
HRHelena Ramos
Helena Ramos
The current paper aims at the assessment of the effectiveness of a popular transient-based technique—inverse transient analysis (ITA)—for leak detection in water pipe systems using physical data. Data were collected from two pipe systems made of polyethylene: a laboratory facility at Imperial College London and a quasi-field system at Thames Water Utilities. A hydraulic transient solver especially developed for viscoelastic pipes (typically made of polyethylene) and an optimization algorithm for the simultaneous creep calibration and leak location have been developed for the application of this technique. The evaluation of the presence, location, and size of leaks was carried out using collected data. ITA allowed for the identification of the approximate location of leaks as long as the physical characteristics of the pipeline are well known, the transient is generated by a fast change of flow conditions, the leak has a “reasonable size,” and the transient solver is accurate enough to describe the transient event.

1 January 2004 in Journal of Hydraulic Research
Verified
Journal Article
Closed access
DCDídia Isabel Cameira Covas
Dídia Isabel Cameira Covas
ISIvan Stoianov
Ivan Stoianov
HRHelena Ramos
Helena Ramos
NGNigel Graham
Nigel Graham
CMCedo Maksimovic
Cedo Maksimovic
The mechanical behaviour of the pipe material determines the pressure response of a fluid system during the occurrence of transient events. in viscoelastic pipes, typically made of polyethylene (pe), maximum or minimum transient pressures are rapidly attenuated and the overall pressure wave is delayed in time. this is a result of the retarded deformation of the pipe-wall. this effect has been observed in transient data collected in a high-density pe pipe-rig, at imperial college (london, uk). several transient tests were carried out to collect pressure and circumferential strain data. the pipe material presented a typical viscoelastic mechanical behaviour with a sudden pressure drop immediately after the fast valve closure, a major dissipation and dispersion of the pressure wave, and transient mechanical hysteresis. the creep-function of the pipe material was experimentally determined by creep tests, and, its order-of-magnitude was estimated based on pressure-strain data collected from the pipe-rig. a good agreement between the creep functions was observed. creep tests are important for the characterization of the viscoelastic behaviour of pe as a material; however, when pe is integrated in a pipe system, mechanical tests only provide an estimate of the actual mechanical behaviour of the pipe system. this is because creep depends on not only the molecular structure of the material and temperature but also on pipe axial and circumferential constraints and the stress-time history of the pipe system.

1 December 2005 in Journal of Hydraulic Engineering
Verified
Journal Article
Closed access
DCDídia Isabel Cameira Covas
Dídia Isabel Cameira Covas
HRHelena Ramos
Helena Ramos
AAA. Betâmio de Almeida
A. Betâmio de Almeida
The current paper focuses on leakage detection in pipe systems by means of the standing wave difference method (SWDM) used for cable fault location in electrical engineering. This method is based on the generation of a steady-oscillatory flow in a pipe system, by the sinusoidal maneuver of a valve, and the analysis of the frequency response of the system for a certain range of oscillatory frequencies. The SWDM is applied to several configurations of pipe systems with different leak locations and sizes. A leak creates a resonance effect in the pressure signal with a secondary superimposed standing wave. The pressure measurement and the spectral analysis of the maximum pressure amplitude at the excitation site enable the identification of the leak frequencies and, consequently, the estimation of the leak approximate location. Practical difficulties of implementation of this technique in real life systems are discussed.

1 September 2008 in Journal of Hydraulic Engineering
Verified
Journal Article
Closed access
ASAlexandre Kepler Soares
Alexandre Kepler Soares
DCDídia Isabel Cameira Covas
Dídia Isabel Cameira Covas
LRLuisa Fernanda Reis
Luisa Fernanda Reis
This research work focuses on the analysis of hydraulic transients in polyvinyl chloride (PVC) pipes, which are characterized by a viscoelastic rheological behavior. Transient pressure data were collected in a pipe rig consisting of a set of PVC pipes. The creep function of the PVC pipes was determined by using an inverse transient model based on collected transient pressure data and compared with that obtained by carrying out mechanical tensile tests of PVC pipe specimens. The numerical results obtained from the transient solver have shown that the attenuation, dispersion, and shape of transient pressures were well described. The incorporation of the viscoelastic mechanical behavior in the hydraulic transient model has provided an excellent fitting between numerical results and observed data. Calibrated creep function based on inverse analysis fit the one determined by mechanical tests well, which emphasized the importance of pipe-wall viscoelasticity in hydraulic transients in PVC pipes.

1 May 2008 in Journal of Hydraulic Research
Verified
Journal Article
Closed access
ABAnton Bergant
Anton Bergant
ATArris Tijsseling
Arris Tijsseling
JVJohn P. Vítkovský
John P. Vítkovský
DCDídia Isabel Cameira Covas
Dídia Isabel Cameira Covas
ASAngus R. Simpson
Angus R. Simpson
MLMartin F. Lambert
Martin F. Lambert
This two-part paper investigates key parameters that may affect the pressurewaveform predicted by the classical theory ofwater-hammer. Shortcomings in the prediction of pressure wave attenuation, s...