Mohammed EL GIBARI

Dr. Mohammed EL GIBARI

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2016 in Optics Communications
Verified
Journal Article
Closed access
MHMassinissa Hadjloum
Massinissa Hadjloum
Mohammed EL GIBARIMohammed EL GIBARI
Mohammed EL GIBARI
HLHongwu Li
Hongwu Li
ADAfshin S. Daryoush
Afshin S. Daryoush

24 June 2010 in Electronics Letters
Verified
Journal Article
Closed access
Mohammed EL GIBARIMohammed EL GIBARI
Mohammed EL GIBARI
DAD. Averty
D. Averty
CLC. Lupi
C. Lupi
MBM. Brunet
M. Brunet
HLH. Li
H. Li
STS. Toutain
S. Toutain
A study of back-to-back grounded coplanar waveguide-microstrip (GCPW-MS) transitions is presented. By using low-permittivity substrates, both the attenuation and the bandwidth can be improved. An ultra-broad bandwidth up to 77 GHz could be obtained with the BCB polymer as substrate in thin film on low-resistivity silicon wafers.

5 October 2015 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
MHMassinissa Hadjloum
Massinissa Hadjloum
Mohammed EL GIBARIMohammed EL GIBARI
Mohammed EL GIBARI
HLHongwu Li
Hongwu Li
ADAfshin S. Daryoush
Afshin S. Daryoush
An ultra-wideband complex permittivity extraction method is reported here using numerical fitting of scattering parameters to measured results. A grounded coplanar waveguide transmission line is realized on an unknown dielectric material, whose dielectric constant and loss tangent are extracted by the best fitting of the simulated magnitude, |S21|, and phase, ϕ21, of forward scattering parameter using an electromagnetic full-wave simulator (high frequency structure simulator) to the measured results. The genetic algorithm is employed for optimum rapid extraction, where errors between the numerically simulated and measured S21 (|S21| and ϕ21) are minimized in an iterative manner. As long as the convergence criterion is not satisfied, modifications to dielectric properties are made with this genetic algorithm implemented in Matlab. Feasibility of this extraction technique is validated on benzocyclobutane polymer from 10 MHz to 40 GHz.

26 June 2015 in Microwave and Optical Technology Letters
Verified
Journal Article
Closed access
PDF file
Mohammed EL GIBARIMohammed EL GIBARI
Mohammed EL GIBARI
DADominique Averty
Dominique Averty
MHMathieu Halbwax
Mathieu Halbwax
JVJean-Pierre Vilcot
Jean-Pierre Vilcot
HLHongwu Li
Hongwu Li

29 December 2015 in International Journal of Antennas and Propagation
Verified
Journal Article
Open access
PDF file
Mohammed EL GIBARIMohammed EL GIBARI
Mohammed EL GIBARI
HLHongWu Li
HongWu Li
A comparative study between via-holed and via-free back-to-back GCPW-MS-GCPW (Grounded Coplanar Waveguide-Microstrip lines) transitions is reported in this paper. According to simulation results, both via-holed and via-free transitions on commercial benzocyclobutene polymer 20 µm film show a bandwidth over 57 GHz. Bandwidth of optimized via-holed transitions increases with the via-hole diameter, up to 75 GHz with 300 μm via-hole diameter. The via-hole free transition achieves experimentally an ultrabroadband from 2 GHz to 78 GHz with an insertion loss of only 0.5 dB thanks to the copper metallization thickness of 2 μm. In addition, these measurement results are in perfect agreement with the simulation results. These via-free and via-holes transitions are very useful and requested in component packaging, on-wafer measurements of microstrip based microwave integrated circuits, and also the interconnections in hybrid circuits including both microstrip and coplanar structures.

5 March 2010 in Microwave and Optical Technology Letters
Verified
Journal Article
Open access
PDF file
Mohammed EL GIBARIMohammed EL GIBARI
Mohammed EL GIBARI
DADominique Averty
Dominique Averty
CLCyril Lupi
Cyril Lupi
HLHongwu Li
Hongwu Li
STSerge Toutain
Serge Toutain
Electro‐optic modulators are key components in high bit‐rate optical transmissions. Decreasing the manufacturing cost without damage on performances is one of the most challenging issues for such components. We demonstrate that the electro‐optic modulators based on polymer are compatible with high bandwidth requirements. Indeed, according to the results obtained by numerical simulation and partly validated by experiments, with the via‐free GCPW‐MS‐GCPW electrodes proposed and analyzed in this article, the (400 MHz–67 GHz) bandwidth is achievable with electro‐optic modulators based on suitable polymers. These encouraging results are very useful for low‐cost mass production of polymer‐based electro‐optic modulators for a wide range of applications: digital and analogue high bit‐rate transmissions.© 2010 Wiley Periodicals, Inc. Microwave Opt Technol Lett 52: 1078–1082, 2010; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.25112