Sergii Maksimov

Dr. Sergii Maksimov

E.O.Paton Electric Welding Institute
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2013 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
CJChuanbao Jia
Chuanbao Jia
TZTao Zhang
Tao Zhang
SMSergii Maksimov
Sergii Maksimov
XYXin Yuan
Xin Yuan

3 July 2017 in Welding in the World
Verified
Journal Article
Closed access
PDF file
NGNing Guo
Ning Guo
YDYongpeng Du
Yongpeng Du
SMSergii Maksimov
Sergii Maksimov
JFJicai Feng
Jicai Feng
ZYZiqiang Yin
Ziqiang Yin
YFYunlong Fu
Yunlong Fu

27 April 2010 in Welding International
Verified
Journal Article
Closed access
SMSergii Maksimov
Sergii Maksimov
(2010). Underwater arc welding of higher strength low-alloy steels. Welding International: Vol. 24, No. 6, pp. 449-454.

11 January 2017 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
JWJianxin Wang
Jianxin Wang
JSJiahui Shi
Jiahui Shi
JWJiayou Wang
Jiayou Wang
WLWenhang Li
Wenhang Li
CLChuan Liu
Chuan Liu
QZQing Zhu
Qing Zhu

6 August 2021 in Metals
Verified
Journal Article
Open access
PDF file
MZMaofu Zhang
Maofu Zhang
YHYanfei Han
Yanfei Han
CJChuanbao Jia
Chuanbao Jia
SDShengfa Dong
Shengfa Dong
SMSergii Maksimov
Sergii Maksimov
CWChuansong Wu
Chuansong Wu
In underwater wet welding, the unstable welding process caused by the generation and rupture of bubbles and the chilling effect of water on the welding area result in low quality of welded joints, which makes it difficult to meet the practical application of marine engineering. To improve the process stability and joining quality, a mixture of welding flux with a water glass or epoxy resin was placed on the welding zone before underwater welding. In this paper, welds’ appearance, geometry statistics of welds’ formation, welding process stability, slag structure, microstructure, pores and mechanical properties were investigated. It was found that with the addition of water glass in the mixture, the penetration of weld was effectively increased, and the frequency of arc extinction was reduced. Though the porosity rose to a relatively high level, the joints’ comprehensive mechanical properties were not significantly improved. Notably, the applied epoxy resin completely isolated the surrounding water from the welding area, which greatly improved process stability. Furthermore, it benefited from the microstructure filled with massive acicular ferrite, the average elongation and room temperature impact toughness increased by 178.4%, and 69.1% compared with underwater wet welding, respectively, and the bending angle of the joint reaches to 180°.

9 November 2023 in Metals
Verified
Journal Article
Open access
PDF file
YHYanfei Han
Yanfei Han
CJChuanbao Jia
Chuanbao Jia
CHChen He
Chen He
MZMaofu Zhang
Maofu Zhang
SMSergii Maksimov
Sergii Maksimov
CWChuansong Wu
Chuansong Wu
The physical phenomena of submerged arc welding (SAW) conducted with a 1.6 mm flux-cored wire were investigated using X-ray imaging technique. Three kinds of metal transfer modes were confirmed in this paper, namely the front flux wall-guided droplet transfer, back flux wall-guided droplet transfer, and repelled droplet transfer, of which the corresponding percentages were 47.65%, 45.29%, and 7.06%, respectively. Although the average sizes of the droplets for SAW and FCAW (flux-cored wire welding) were 2.0 mm and 1.9 mm with an average droplet transfer time of 90.3 ms, it required 36.4% more time for the droplet of SAW to finish one metal transfer than it did in FCAW. In addition, the volume of the cavity was not constant but repeated a cycle mode of “expansion and contraction” during the whole process. Thus, the dynamics of the cavity and viscous resistance caused by the flux collectively slowed down the velocity of the droplets from the wire to the weld pool in SAW. Compared with FCAW, a smoother weld without pits and pores was manufactured during the SAW process. Due to the compression effect of the flux, the 14.5 mm average weld width of SAW was 2.9 mm shorter than that of the FCAW. Furthermore, the thickness of slag with a porous structure in SAW was 2.7 times of that in FCAW, indicating that it could provide better protection to the weld of SAW.