In this study, copper bismuth oxide (CuBi2O4) absorber-based thin film heterojunction solar cell structure consisting of Al/FTO/CdS/CuBi2O4/Ni has been proposed. The proposed solar cell device structure has been modeled and analyzed by using the solar cell capacitance simulator in one dimension (SCAPS-1D) software program. The performance of the proposed photovoltaic device is evaluated numerically by varying thickness, doping concentrations, defect density, operating temperature, back metal contact work function, series and shunt resistances. The current density–voltage behaviors at dark and under illumination are investigated. To realize the high efficiency CuBi2O4-based solar cell, the thickness, acceptor and donor densities, defect densities of different layers have been optimized. The present work reveals that the power conversion efficiency can be enhanced by increasing the absorber layer thickness. The efficiency of 26.0% with open-circuit voltage of 0.97 V, short-circuit current density of 31.61 mA/cm2, and fill-factor of 84.58% is achieved for the proposed solar cell at the optimum 2.0-μm-thick CuBi2O4 absorber layer. It is suggested that the p-type CuBi2O4 material proposed in the present study can be employed as a promising absorber layer for applications in the low cost and high efficiency thin-film solar cells.
In this work, copper nickel tin sulfide (Cu2NiSnS4) as an encouraging alternative absorber for thin-film photovoltaic devices is explored. Here, the Cu2NiSnS4 (CNTS) absorber-based heterojunction solar cell is designed through a two-stage theoretical approach using Solar Cell Capacitance Simulator in one-dimension (SCAPS-1D). Initially four different hole transport materials (MoO3, SnS, NiOx, and PEDOT.PSS) are incorporated at the back interface in experimentally configured Au/Cu2NiSnS4/ZnS/ZnO/ITO cell to boost the device outputs. The MoO3 semiconductor is anticipated as a hole transport layer (HTL) in the heterojunction Ni/MoO3/Cu2NiSnS4/ZnS/ZnO/ITO solar configuration. It is revealed that an appropriate band alignment can be formed at MoO3/Cu2NiSnS4 interface with less interfacial defects among other HTLs with CNTS absorber, thus improving the solar cell outputs. Efficiency is increased from 2.71% to 8.79% for the proposed CNTS-based solar cell. Further optimization is accomplished concerning thickness, defect states, and doping density of the various materials utilized in the heterojunction structure. Defect characteristics at the MoO3/Cu2NiSnS4 and Cu2NiSnS4/ZnS interfaces are also evaluated and optimized to boost the conversion efficiency significantly. Moreover, the effects of operating temperature and rear electrode work function on the outputs of the designed solar device are studied. The aforesaid two-stage optimization yields efficiency of 12.46% with VOC of 1.23 V, JSC of 12.66 mA/cm2, and FF of 79.78%. Therefore, these findings will facilitate the scientific communities to further progress an economical and extremely efficient CNTS-based solar device with a promising MoO3 HTL.
Tin-based halide perovskite compounds have attracted enormous interest as effective replacements for the conventional lead halide perovskite solar cells (PCSs). However, achieving high efficiency for tin-based perovskite solar cells is still challenging. Herein, we introduced copper sulfide (CuS) as a hole transport material (HTM) in lead free tin-based B-γ-CsSnI3 PSCs to enhance the photovoltaic (PV) performances. The lead free tin-based CsSnI3 perovskite solar cell structure consisting of CuS/CsSnI3/TiO2/ITO was modeled and the output characteristics were investigated by using the one dimensional solar cell capacitance simulator (SCAPS-1D). The CuS hole transport layer (HTL) with proper band arrangement may notably minimize the recombination of the charge carrier at the back side of the perovskite absorber. Density functional theory (DFT)-extracted physical parameters including the band gap and absorption spectrum of CuS were used in the SCAPS-1D program to analyze the characteristics of the proposed PV device. The PV performance parameters of the proposed device were numerically evaluated by varying the absorber thickness and doping concentration. In this work, the variation of the functional temperature on the cell outputs was also studied. Furthermore, different HTMs were employed to investigate the PV characteristics of the proposed CsSnI3 PSC. The power conversion efficiency (PCE) of ~29% was achieved with open circuit voltage (Voc) of 0.99 V, a fill factor of ~87%, and short circuit current density (Jsc) of 33.5 mA/cm2 for the optimized device. This work addressed guidelines and introduced a convenient approach to design and fabricate highly efficient, inexpensive, and stable lead free tin-based perovskite solar cells.