Andres Tovar

Dr. Andres Tovar

Mechanical Engineering, Purdue University West Lafayette, West Lafayette, Indiana, USA
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2017 in Computers & Structures
Verified
Journal Article
Closed access
TWTong Wu
Tong Wu
KLKai Liu
Kai Liu
Andres TovarAndres Tovar
Andres Tovar

26 February 2022 in Journal of Power Sources
Verified
Journal Article
Closed access
HVHomero Valladares
Homero Valladares
Tianyi LiTianyi Li
Tianyi Li
LZLikun Zhu
Likun Zhu
HEHazim El-Mounayri
Hazim El-Mounayri
AHAhmed M. Hashem
Ahmed M. Hashem
Andres TovarAndres Tovar
Andres Tovar

21 December 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
HWHua Wang
Hua Wang
Tianyi LiTianyi Li
Tianyi Li
Ahmed HashemAhmed Hashem
Ahmed Hashem
AAAshraf Abdel-Ghany
Ashraf Abdel-Ghany
RERasha Eltawil
Rasha Eltawil
Christian M. JulienChristian M. Julien
Christian M. Julien
This work aimed at synthesizing MoO3 and MoO2 by a facile and cost-effective method using extract of orange peel as a biological chelating and reducing agent for ammonium molybdate. Calcination of the precursor in air at 450 °C yielded the stochiometric MoO3 phase, while calcination in vacuum produced the reduced form MoO2 as evidenced by X-ray powder diffraction, Raman scattering spectroscopy, and X-ray photoelectron spectroscopy results. Scanning and transmission electron microscopy images showed different morphologies and sizes of MoOx particles. MoO3 formed platelet particles that were larger than those observed for MoO2. MoO3 showed stable thermal behavior until approximately 800 °C, whereas MoO2 showed weight gain at approximately 400 °C due to the fact of re-oxidation and oxygen uptake and, hence, conversion to stoichiometric MoO3. Electrochemically, traditional performance was observed for MoO3, which exhibited a high initial capacity with steady and continuous capacity fading upon cycling. On the contrary, MoO2 showed completely different electrochemical behavior with less initial capacity but an outstanding increase in capacity upon cycling, which reached 1600 mAh g−1 after 800 cycles. This outstanding electrochemical performance of MoO2 may be attributed to its higher surface area and better electrical conductivity as observed in surface area and impedance investigations.

2 July 2013 in Journal of Mechanical Design
Verified
Journal Article
Closed access
PDF file
PBPunit Bandi
Punit Bandi
JSJames P. Schmiedeler
James P. Schmiedeler
Andres TovarAndres Tovar
Andres Tovar

1 April 2019 in Composite Structures
Verified
Journal Article
Closed access
SRSajjad Raeisi
Sajjad Raeisi
JKJavad Kadkhodapour
Javad Kadkhodapour
Andres TovarAndres Tovar
Andres Tovar

2 December 2019 in Biotechnology and Bioengineering
Verified
Journal Article
Open access
PDF file
TST. J. Sego
T. J. Sego
MPMatthew Prideaux
Matthew Prideaux
JSJane Sterner
Jane Sterner
BMBrian Paul McCarthy
Brian Paul McCarthy
Ping LiPing Li
Ping Li
LSLester Jeshua Smith
Lester Jeshua Smith
Natural tissues are incorporated with vasculature which is further integrated with a cardiovascular system responsible for driving perfusion of nutrient‐rich oxygenated blood through the vasculature in order to support cells metabolism within most cell‐dense tissues. Since scaffold‐free biofabricated tissues being developed into clinical implants, research models, and pharmaceutical testing platforms should similarly exhibit perfused tissue‐like structures, we generated a generalizable biofabrication method resulting in Self‐Supporting Perfused (SSuPer) tissue constructs incorporated with perfusible microchannels and integrated with the modular FABRICA perfusion bioreactor. As proof of concept, we perfused an MLO‐A5 osteoblast‐based SSuPer tissue in the FABRICA. Although our resulting SSuPer tissue replicated vascularization and perfusion observed in situ, supported its own weight, and stained positively for mineral using Von Kossa staining, our in vitro results indicated that computational fluid dynamics (CFD) should be used to drive future construct design and flow application prior to further tissue biofabrication and perfusion. We built a CFD model of the SSuPer tissue integrated in the FABRICA and analyzed flow characteristics (net force, pressure distribution, shear stress, and oxygen distribution) through five SSuPer tissue microchannel patterns in two flow directions and at increasing flow rates. Important flow parameters include flow direction, fully‐developed flow, and tissue microchannel diameters matched and aligned with bioreactor flow channels. We observed that the SSuPer tissue platform is capable of providing direct perfusion to tissue constructs and proper culture conditions (oxygenation, with controllable shear and flow rates), indicating that our approach can be used to biofabricate tissue representing primary tissues and that we can model the system in silico.