To reduce the cost of bacterial cellulose (BC) production, the possibility of using acetone‐butanol‐ethanol (ABE) fermentation wastewater with high COD value (18 050 mg l−1) for BC production by Gluconacetobacter xylinus was evaluated. After 7 days of fermentation, the highest BC yield (1·34 g l−1) was obtained. The carbon sources including sugars (glucose and xylose), organic acids (acetic acid and butyric acid) and alcohol compounds (ethanol and butanol) were utilized by G. xylinus simultaneously during fermentation. Although the COD decrease ratio (about 14·7%) was low, the highest BC yield on COD consumption (56·2%, g g−1) was relatively high and the remaining wastewater could be used for further BC fermentation. Besides, the environment of ABE fermentation wastewater showed small influence on the BC structure by comparison with the BC products obtained in traditional HS medium using field emission scanning electron microscope (FE‐SEM), Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD). Overall, ABE fermentation wastewater is one promising substrate for BC production. Significance and Impact of the Study The possibility of using acetone‐butanol‐ethanol (ABE) fermentation wastewater for bacterial cellulose (BC) production by Gluconacetobacter xylinus was evaluated in this study. This is the first time that ABE fermentation wastewater was used as substrate for BC fermentation. The results provide detail information of metabolism of G. xylinus in ABE fermentation wastewater and the influence of wastewater environment on the structure of BC samples. Overall, this bioconversion could reduce the cost of BC production greatly.
17 December 2013 in Applied Biochemistry and Biotechnology
Although litchi has both nutrient and edible value, the extremely short preservation time limited its further market promotion. To explore processed litchi products with longer preservation time, litchi extract was selected as an alternative feedstock for production of bacterial cellulose (BC). After 2 weeks of static fermentation, 2.53 g/L of the BC membrane was obtained. The trace elements including magnesium (Mg) and sodium (Na) in the litchi extract were partly absorbed in the BC membrane, but no potassium (K) element was detected in it, curiously. Scanning electron microscope (SEM) photographs exhibited an ultrafine network nanostructure for the BC produced in the litchi extract. Analysis of the fourier-transform infrared spectroscopy (FTIR) confirmed the pellicles to be a cellulosic material. Interestingly, X-ray diffraction (XRD) results showed the BC membrane obtained from litchi extract had higher crystallinity of 94.0% than that from HS medium. Overall, the work showed the potential of producing high value-added polymer from litchi resources.
26 November 2014 in Applied Biochemistry and Biotechnology
Bacterial cellulose (BC) has great potential to be used as a new filler in reinforced isotactic polypropylene (iPP) due to its characteristics of high crystallinity, biodegradability and efficient mechanical properties. But the compatibility between BC and iPP is poor. The esterification modified BC (CO) and addition of maleic anhydride grafted polypropylene (MAPP) as a compatibilizer were both used to improve interfacial compatibility of iPP and BC to prepare iPP/BC composites, and the non-isothermal crystallization behavior of isotactic polypropylene/bacterial cellulose composites was discussed. The results showed that with the addition of CO or MAPP, the compatibility of iPP/BC composites greatly improved. Moreover, BC addition was found to enhance iPP crystallization due to homogeneous and heterogeneous nucleation effects. In non-isothermal crystallization kinetics, it was found that the Jeziorny method and ϕ–t analysis are more accurate to describe non-isothermal crystallization behavior of iPP/BC composites. The results showed that the non-isothermal crystallization rates increase in the order of iPP/BC2, iPP, iPP/CO2, and M-iPP/BC3, indicating that the compatibility of iPP/BC composites. Moreover, the cooling rate have greatly influence on non-isothermal crystallization behavior of iPP/BC composites.