Gel syneresis is a common problem in gel treatment for oil recovery applications. In this study, a stable gel was prepared in a soft brine by using a water-soluble phenolic resin as a crosslinker, nanoparticles as a stabilizer, and partially hydrolyzed polyacrylamide (HPAM) or copolymers with different contents of 2-acrylamido-2-methylpropane sulfonic acid (AMPS) groups as polymers. The syneresis behavior of the gels formed in a soft brine was evaluated upon aging in hard brines. The results show that when the salinity of the hard brine is lower than 30,000 mg/L, the gel expands, and its strength decreases; when the salinity of the hard brine is higher than 50,000 mg/L, the gel exhibits syneresis, and its strength increases. The effects of various influencing factors on the gel syneresis behavior were also evaluated. It was found that optimizing the polymer structure and adding nanoparticles can effectively overcome gel syneresis and enhance gel stability. Based on the research described in this paper, some proposals for designing salt-resistant polymer gels are presented.
The properties of a reinforced gel with partially hydrolyzed polyacrylamide (HPAM) as the main agent, water-soluble phenolic resin (WSPR) as the crosslinker, and nano-SiO2 as the stabilizer were evaluated in terms of gelation time, gel strength and thermal stability under the conditions of 110 °C and 12.124 g/L salinity in water. The results showed that the gelation time of the gel with high strength was adjustable from 3 to 23 h, remaining stable for more than 180 days under stratigraphic conditions, although with a certain degree of early dehydration in the gel. Cryo-scanning electron microscopy (cryo-SEM) and dynamic light scattering (DLS) analysis revealed that nano-SiO2 improves the dispersion of the polymer in water, resulting in a more homogeneous structure of the formed gel and thus improving the strength of the gels. In addition, rheological tests and cryo-SEM showed that the interaction between nano-SiO2 and the polymer could inhibit the degradation of polymer to a certain extent and improve the thermal stability of the gel. However, the oxidative degradation of the gel is still the main cause of early dehydration of water-soluble phenolic resin gel, and the addition of a small amount of hydroquinone to the gelants can significantly improve the antioxidative degradation properties of phenolic resin gel.
1 January 2022 in Journal of Petroleum Science and Engineering
Summary: A high-strength gel was prepared by crosslinking a high-concentration but low molecular weight polyacrylamide-tert-butyl acrylate (PAtBA) copolymer with polyethyleneimine (PEI), and the various factors affecting the gelling were systematically evaluated. The results showed that, besides the concentration of polymer and crosslinker, the molecular weight of PEI, pH value and salinity of gelant, and temperature all affected the gelation time, gel strength, and stability. High-strength PAtBA-PEI gels could be stable for more than 240 days in synthetic brine with salinity less than 43 530 mg/L at a temperature not higher than 130°C. However, when the temperature is higher than 150°C, the gel would be broken within 60 days. When the salinity in the synthetic brine was too high, the gel also exhibited syneresis at 110°C within 15 days. X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) analysis showed that the syneresis of PAtBA-PEI gel under high-salinity conditions was caused by the reaction of carboxylate group generated by the hydrolysis of the amide group with divalent cations. In addition, Cryo-scanning electron microscope (Cryo-SEM) analysis showed that high-strength PAtBA-PEI gels had high crosslinking density and poor deformation ability. Nevertheless, the results of rheological tests and flooding experiments showed that the low deformation ability of the gel did not affect the sealing ability of the gel, and the high storage modulus and yield stress of the gel enabled it to exhibit high breakthrough pressure and residual resistance factor in the core. The results of this study are instructive for the field application of PEI gels.
Summary: By using an acrylamide (AM)-acrylamide propyl sulfonate (AMPS) copolymer crosslinked with hydroquinone (HQ) and hexamethylenetetramine (HMTA), a stable gel was prepared at 150℃ in simulated brine with a salinity of 25×104 mg/L. The gelation time, strength, and thermal stability of gel were investigated, and the results indicated that the dosage of the crosslinker was the key factor controlling the stability and gelation time of gel. When the polymer concentration was more than 0.7 wt% and the concentrations of HQ and HMTA were more than 0.2 wt%, respectively, a gel aged under high temperature and high salinity for 180 days could be obtained, but its gelation time was short and could be extended by adding lauramidopropyl hydroxy sulfobetaine (LHSB). When the crosslinker concentration was low, the gel would exhibit syneresis problems after aging at 150℃. Cryo-scanning electron microscopy (cryo-SEM), 13C nuclear magnetic resonance (13C-NMR), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) analyses showed that the presence of AMPS in the crosslinked polymer controlled the gel resistance to high temperature and high salinity. Using AM-AMPS copolymer with high AMPS content and regulating the crosslinker concentration can effectively inhibit the intramolecular catalytic hydrolysis of AMPS and enhance the stability of gel. The research results could guide the design and development of gels for conformance control in high-temperature and high-salinity reservoirs.