The increasing number of electronic devices on board and the use of novel composite materials in the aerospace industry create a harsh electromagnetic environment that must be studied. In this article, a UAV demonstrator (DEMO-E3) with different test cases is evaluated through the low-level swept field test following a nested resonant chambers approach, which is framed under the high intensity radio frequency measurements. The aim is to analyze the difference in terms of the shielding effectiveness of the enclosure considering the different materials and apertures of each test sample. Some of the test cases had been previously measured independently, according to the IEC 61000-4-21 standard, while in this study, they are incorporated into the demonstrator and former results are used as a comparison.
The tendency over the last decades in the aerospace industry is to substitute classic metallic materials with new composite materials such as carbon fiber composites (CFC), fiber glass, etc., as well as adding electronic devices to ensure the safety and proper platform operation. Due to this, to protect the aircraft against the Electromagnetic Environmental Effects (E3), it is mandatory to develop accurate electromagnetic (EM) characterization measurement systems to analyze the behavior of new materials and electronic components. In this article, several measurement methods are described to assess the EM behavior of the samples under test: microstrip transmission line for a surface current analysis, free space to obtain intrinsic features of the materials and shielding effectiveness (SE) approaches to figure out how well they isolate from EM fields. The results presented in this work show how the different facilities from the National Institute of Aerospace Technology (INTA) are suitable for such purposes, being capable of measuring a wide variety of materials, depending on the type of test to be carried out.
The development of devices for In-Situ Resource Utilization (ISRU) of the lunar surface powder (regolith) by means of microwaves needs regolith simulants with electromagnetic properties similar to the lunar regolith. This document deals with the measurement of complex permittivity and dielectric loss tangent of the aforementioned simulants at ambient temperature from 400 MHz to 20 GHz. In addition, further studies are carried out taking into account humidity of the samples and their densities. The obtained results will be applicable for comparing the measured values of EAC-1A and JSC-2A among them and with other previously measured simulants and real samples. The measurements are carried out applying two different nonresonant techniques: Open- Ended Coaxial Probe (OECP) and Transmission Line. For this purpose, the DAK and EpsiMu commercial kits were respectively used.
The development of devices for the in situ resource utilization (ISRU) of lunar surface powder (regolith) by means of microwaves needs regolith simulants with electromagnetic properties similar to the lunar regolith. This document deals with the measurement of complex permittivity and dielectric loss tangent of the aforementioned simulants at ambient temperature from 400 MHz to 20 GHz, performing measurements using two lunar dust simulants, EAC-1A and JSC-2A, resulting, on the one hand, in permittivity values of for the EAC-1A lunar dust simulant and for the JSC-2A simulant, and on the other hand, in loss tangent values of for the EAC-1A powder and for the JSC-2A powder. In addition, further studies are carried out taking into account the humidity of the samples and their densities at room temperature. The obtained results are applicable for comparing the measured values of EAC-1A and JSC-2A between them and with other previously measured simulants and real samples. The measurements are carried out by applying two different nonresonant techniques: Open-Ended Coaxial Probe (OECP) and transmission line. For this purpose, the DAK and EpsiMu commercial kits are used, respectively.
Spaceflight instruments must undergo electromagnetic compatibility (EMC) testing under strict contamination-control requirements. In this context, local RF-transparent protective covers may be considered when the test facility cannot provide the required cleanliness conditions around the hardware. This work presents an application-oriented electromagnetic assessment of candidate RF-transparent protective covers for contamination-sensitive EMC testing. Several candidate materials are characterized using the open-ended coaxial probe (OECP) technique over the 2–20 GHz band to determine their effective dielectric properties and estimate their normal-incidence flat-wall transmission coefficients. Full-cover transfer-function (TF) measurements are then performed at INTA’s BIANCHA free-space anechoic facility over the 4.5–8 GHz band, using two receiving antennas with complementary radiation characteristics: a pyramidal horn and a top-hat bicone. Hemispherical covers fabricated with five candidate materials are first assessed, including repeatability and time-domain gating analyses. An alternative cubic cover is then evaluated to study the influence of cover geometry, angular incidence and edge/corner effects. An additional -based mismatch assessment is also performed to distinguish antenna input-matching effects from broader system-level antenna–cover interactions. The results show that low-loss dielectric covers can introduce limited TF perturbations within the tested free-space configuration, while also demonstrating that cover geometry has a significant impact on the angular stability of the measured response. The conclusions are therefore restricted to the experimentally validated 4.5–8 GHz BIANCHA configuration.