Thierry Decker

Dr. Thierry Decker

University of Luxembourg, Luxembourg, Luxembourg
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
SKSlawomir Kedziora
Slawomir Kedziora
TDThierry Decker
Thierry Decker
EMElvin Museyibov
Elvin Museyibov
JMJulian Morbach
Julian Morbach
SHSteven Hohmann
Steven Hohmann
MWMichael Wahl
Michael Wahl
The number of additive manufacturing methods and materials is growing rapidly, leaving gaps in the knowledge of specific material properties. A relatively recent addition is the metal-filled filament to be printed similarly to the fused filament fabrication (FFF) technology used for plastic materials, but with additional debinding and sintering steps. While tensile, bending, and shear properties of metals manufactured this way have been studied thoroughly, their fatigue properties remain unexplored. Thus, the paper aims to determine the tensile, fatigue, and impact strengths of Markforged 17-4 PH and BASF Ultrafuse 316L stainless steel to answer whether the metal FFF can be used for structural parts safely with the current state of technology. They are compared to two 316L variants manufactured via selective laser melting (SLM) and literature results. For extrusion-based additive manufacturing methods, a significant decrease in tensile and fatigue strength is observed compared to specimens manufactured via SLM. Defects created during the extrusion and by the pathing scheme, causing a rough surface and internal voids to act as local stress risers, handle the strength decrease. The findings cast doubt on whether the metal FFF technique can be safely used for structural components; therefore, further developments are needed to reduce internal material defects.

27 March 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TDThierry Decker
Thierry Decker
SKSlawomir Kedziora
Slawomir Kedziora
This study explores the complete production chain of designing, optimizing, and Additive Manufacturing (AM) of a helmet incorporating a functionally graded lattice structure (FGLS). The potential of FGLSs in impact energy absorption tasks is investigated, along with the demonstration of a novel lattice optimization approach. Fifteen conformal, strut-based lattices are implemented in a realistic mountain bike helmet geometry and simulated in a standardized impact scenario in accordance with EN 1078. One model is subjected to the optimization procedure, produced, and physically tested. The study addresses limitations in prior research, emphasizing manufacturability in an AM context, lattice type exploration, the comparability of different unit cell types, and numerical modeling choices. The findings provide insights into the performance of lattice structures during impact, emphasizing practical engineering aspects such as design choices, optimization approaches, and manufacturing constraints.

15 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
SKSlawomir Kedziora
Slawomir Kedziora
TDThierry Decker
Thierry Decker
EMElvin Museyibov
Elvin Museyibov
The significance of lightweight designs has become increasingly paramount due to the growing demand for sustainability. Consequently, this study aims to demonstrate the potential of utilising a functionally graded lattice as an infill structure in designing an additively manufactured bicycle crank arm to achieve construction lightness. The authors seek to determine whether functionally graded lattice structures can be effectively implemented and explore their potential real-world applications. Two aspects determine their realisations: the lack of adequate design and analysis methods and the limitations of existing additive manufacturing technology. To this end, the authors employed a relatively simple crank arm and design exploration methods for structural analysis. This approach facilitated the efficient identification of the optimal solution. A prototype was subsequently developed using fused filament fabrication for metals, enabling the production of a crank arm with the optimised infill. As a result, the authors developed a lightweight and manufacturable crank arm showing a new design and analysis method implementable in similar additively manufactured elements. The percentage increase of a stiffness-to-mass ratio of 109.6% was achieved compared to the initial design. The findings suggest that the functionally graded infill based on the lattice shell improves structural lightness and can be manufactured.

12 December 2023 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
TDThierry Decker
Thierry Decker
SKSlawomir Kedziora
Slawomir Kedziora
EMElvin Museyibov
Elvin Museyibov
This paper serves as basis for subsequent studies investigating a potential material and manufacturing method selection for producing lattice structures to be used as energy absorption device, such as in novel wearable protective gear. Four additively manufactured plastics from two additive manufacturing methods are examined in detail. Polyamide 12 specimens produced on two Powder Bed Fusion (PBF) machines are compared against specimens produced on a stereolithography (SLA) printer using a standard and an engineering-grade resin. A comprehensive analysis of their mechanical properties is presented by measuring their densities as well as tensile, fatigue, and impact properties. In addition, Poisson’s ratio of the resin materials is estimated using Digital Image Correlation (DIC).

26 April 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
SKSlawomir Kedziora
Slawomir Kedziora
TDThierry Decker
Thierry Decker
EMElvin Museyibov
Elvin Museyibov
The presented research article shows a functionally graded lattice as an infill structure in designing a 3D printed mechanical element—a bicycle crank arm. The authors want to answer the fundamental question: whether the functionally graded lattice structures can efficiently improve structural performance and how they can be implemented in real complex components. Intuitively, everyone senses that using such elements must bring profit. A good example might be nature, which commonly reaches for such a solution in the skeletons of animals and humans. Two aspects determine their realisations: the lack of adequate construction and analysis methods and the limitations of existing manufacturing methods. Thus, the authors used relatively simple crank arm design and design exploration methods for structural analysis. The design exploration method enabled us to find the optimum solution efficiently. A developed prototype was created utilising additive manufacturing. One of the 3D printing methods - fused filament fabrication technology for metals, allowed the prototype of a crank arm with the optimised infill to be made. As a result, the authors developed a lightweight and manufacturable crank arm showing the new construction and analysis method implementable in similar 3D printed elements.

4 December 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TDThierry Decker
Thierry Decker
SKSlawomir Kedziora
Slawomir Kedziora
This paper presents a new method for optimizing the thickness distribution of a functionally graded lattice structure. It links the thickness of discrete lattice regions via mathematical functions, reducing the required number of optimization variables while being applicable to highly nonlinear models and arbitrary optimization goals. This study demonstrates the method’s functionality by altering the local thickness of a lattice structure in compression, optimizing the structure’s specific energy absorption at constant weight. The simulation results suggest significant improvement potential for the investigated Simple Cubic lattice, but less so for the Isotruss variant. The energy absorption levels of the physical test results closely agree with the simulations; however, great care must be taken to accurately capture material and geometry deviations stemming from the manufacturing process. The proposed method can be applied to other lattice structures or goals and could be useful in a wide range of applications where the optimization of lightweight and high-performance structures is required.