Chukwuka Austine Onyenwoke

Mr. Chukwuka Austine Onyenwoke

University of Saskatchewan, Saskatoon, Saskatchewan, Canada
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 March 2023 in Fuels
Verified
Journal Article
Open access
PDF file
COChukwuka Austine Onyenwoke
Chukwuka Austine Onyenwoke
Lope G TabilLope G Tabil
Lope G Tabil
EMEdmund Mupondwa
Edmund Mupondwa
Duncan CreeDuncan Cree
Duncan Cree
PAPhani Adapa
Phani Adapa
Torrefaction pretreatment is a mild form of pyrolysis that has the potential to produce a high-quality raw material for making biofuel that serves as a replacement for coal in the bioenergy industry. Microwave-assisted torrefaction was conducted on white spruce sawdust (WSS) at temperatures of 200 °C, 250 °C, and 300 °C and retention times of 5 min, 7 min, and 9 min in an inert environment. The torrefaction process produces a solid carbon, commonly known as biochar, and condensable (torrefaction liquid (TL)) and non-condensable gases. In this study, torrefaction characteristics were investigated to observe its effects on the thermal and physiochemical properties of the pellets produced. During the torrefaction process, a significant mass loss associated with the decomposition of hemicellulose was observed. The hemicellulose content drastically reduced to approximately 1.8% and the cellulose content was reduced by approximately 10%, while the lignin gained approximately 35% as the severity increased. This led to an improvement in the higher heating value (HHV), hydrophobicity, bulk, particle density, pellet dimensional stability, and pellet density. However, the pellet tensile strength decreased as the torrefaction severity increased. Pellet tensile strength is a critical indicator of biomass pellets that expresses the force required to crush or damage a pellet. Therefore, to enhance the tensile strength of the pellets, the introduction of a binder was necessary. Torrefaction liquid and sawdust were used as additives at different proportions during pelletization. The addition of binders (torrefaction liquid and sawdust) to the pellet formulation increased the tensile strength of the torrefied WSS by approximately 50%. The OH groups in the biomass break down to a limited degree due to dehydration. This hinders the formation of H bonds, thereby increasing the chances that the pretreated biomass will become hydrophobic. The SEM graphs showed that the torrefied WSS pellets demonstrated more firmly glued surfaces with fewer pores spaces when set side by side with the raw pellets. The thermogravimetric analysis conducted showed that the torrefaction of WSS slightly reduced its thermal stability.

29 September 2022 in Energies
Verified
Journal Article
Open access
PDF file
COChukwuka Austine Onyenwoke
Chukwuka Austine Onyenwoke
Lope G TabilLope G Tabil
Lope G Tabil
Tim DumonceauxTim Dumonceaux
Tim Dumonceaux
Duncan CreeDuncan Cree
Duncan Cree
EMEdmund Mupondwa
Edmund Mupondwa
CKChithra Karunakaran
Chithra Karunakaran
Steam explosion pretreatment of sawdust and oat straw under mild, medium, and severe conditions was conducted to improve the quality of pellets generated from these feedstocks. This work examined the effects of temperature, time, and moisture content on the mechanical properties of biomass pellets. From the ANOVA conducted, the p-values of the regression models for all the response variables (dimensional stability, tensile strength, and pellet density) studied were significant (p < 0.05), except for the pellet density of steam-pretreated oat straw pellets. The interaction of these three factors did not significantly affect the response variables of oat straw pellets. In addition, the higher heating value (HHV) of treated biomass increased up to a maximum of about 9.5% and 7% as compared with the non-treated sawdust and oat straw, respectively. In addition, an increment of about 3.6-fold and 3.1-fold in pellet tensile strength of steam-pretreated sawdust and oat straw was observed, respectively. Microstructural examination of the pellets from steam-pretreated biomass revealed that the material contained particles that were more closely bonded and featured a cemented surface with fewer pores when compared to particles from untreated oat straw and sawdust.
1

26 December 2023 in Energies
Verified
Journal Article
Open access
PDF file
COChukwuka Austine Onyenwoke
Chukwuka Austine Onyenwoke
Lope G TabilLope G Tabil
Lope G Tabil
Tim DumonceauxTim Dumonceaux
Tim Dumonceaux
EMEdmund Mupondwa
Edmund Mupondwa
Duncan CreeDuncan Cree
Duncan Cree
OOOnu Onu Olughu
Onu Onu Olughu
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt to 72 kt/year. The scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios, materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with approximately 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The minimum selling prices of the pellets obtained from Scenarios 1–6 were $113.4/t, $118.7/t, $283.4/t, $298.7/t, $200.5/t, and $208.4/t, respectively. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period was found to be sensitive to variations in feedstock cost.

13 November 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
COChukwuka Austine Onyenwoke
Chukwuka Austine Onyenwoke
Lope G TabilLope G Tabil
Lope G Tabil
Tim DumonceauxTim Dumonceaux
Tim Dumonceaux
EMEdmund Mupondwa
Edmund Mupondwa
Duncan CreeDuncan Cree
Duncan Cree
OOOnu Onu Olughu
Onu Onu Olughu
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.