Abnormalities in the ankle contact pressure are related to the onset of osteoarthritis. In vivo measurements are not possible with currently available techniques, so computational methods such as the finite element analysis (FEA) are often used instead. The discrete element method (DEM), a computationally efficient alternative to time-consuming FEA, has also been used to predict the joint contact pressure. It describes the articular cartilage as a bed of independent springs, assuming a linearly elastic behaviour and absence of relative motion between the bones. In this study, we present the extended DEM (EDEM) which is able to track the motion of talus over time. The method was used, with input data from a subject-specific musculoskeletal model, to predict the contact pressure in the ankle joint during gait. Results from EDEM were also compared with outputs from conventional DEM. Predicted values of contact area were larger in EDEM than they were in DEM (4.67 and 4.18 cm2, respectively). Peak values of contact pressure, attained at the toe-off, were 7.3 MPa for EDEM and 6.92 MPa for DEM. Values predicted from EDEM fell well within the ranges reported in the literature. Overall, the motion of the talus had more effect on the extension and shape of the pressure distribution than it had on the magnitude of the pressure. The results indicated that EDEM is a valid methodology for the prediction of ankle contact pressure during daily activities.
Assessment of distal cerebral perfusion after ischaemic stroke is currently only possible through expensive and time-consuming imaging procedures which require the injection of a contrast medium. Alternative approaches that could indicate earlier the impact of blood flow occlusion on distal cerebral perfusion are currently lacking. The aim of this study was to identify novel biomarkers suitable for clinical implementation using less invasive diagnostic techniques such as Transcranial Doppler (TCD). We used 1D modelling to simulate pre- and post-stroke velocity and flow wave propagation in a typical arterial network, and Sobol’s sensitivity analysis, supported by the use of Gaussian process emulators, to identify biomarkers linked to cerebral perfusion. We showed that values of pulsatility index of the right anterior cerebral artery > 1.6 are associated with poor perfusion and may require immediate intervention. Three additional biomarkers with similar behaviour, all related to pulsatility indices, were identified. These results suggest that flow pulsatility measured at specific locations could be used to effectively estimate distal cerebral perfusion rates, and ultimately improve clinical diagnosis and management of ischaemic stroke.
1 September 2021 in Computer Methods and Programs in Biomedicine
Whilst fragility hip fractures commonly affect elderly people, often causing permanent disability or death, they are rarely addressed in advance through preventive techniques. Quantification of bone strength can help to identify subjects at risk, thus reducing the incidence of fractures in the population. In recent years, researchers have shown that finite element models (FEMs) of the hip joint, derived from computed tomography (CT) images, can predict bone strength more accurately than other techniques currently used in the clinic. The specialised hardware and trained personnel required to perform such analyses, however, limits the widespread adoption of FEMs in clinical contexts. In this manuscript we present CT2S (Computed Tomography To Strength), a system developed in collaboration between The University of Sheffield and Sheffield Teaching Hospitals, designed to streamline access to this complex workflow for clinical end-users. The system relies on XNAT and makes use of custom apps based on open source software. Available through a website, it allows doctors in the healthcare environment to benefit from FE based bone strength estimation without being exposed to the technical aspects, which are concealed behind a user-friendly interface. Clinicians request the analysis of CT scans of a patient through the website. Using XNAT functionality, the anonymised images are automatically transferred to the University research facility, where an operator processes them and estimates the bone strength through FEM using a combination of open source and commercial software. Following the analysis, the doctor is provided with the results in a structured report. The platform, currently available for research purposes, has been deployed and fully tested in Sheffield, UK. The entire analysis requires processing times ranging from 3.5 to 8 h, depending on the available computational power. The short processing time makes the system compatible with current clinical workflows. The use of open source software and the accurate description of the workflow given here facilitates the deployment in other centres.
Computational simulations are widely adopted in cardiovascular biomechanics because of their capability of producing physiological data otherwise impossible to measure with non-invasive modalities. Objective. This study presents openBF, a computational library for simulating the blood dynamics in the cardiovascular system. Approach. openBF adopts a one-dimensional viscoelastic representation of the arterial system, and is coupled with zero-dimensional windkessel models at the outlets. Equations are solved by means of the finite-volume method and the code is written in Julia. We assess its predictions by performing a multiscale validation study on several domains available from the literature. Main results. At all scales, which range from individual arteries to a population of virtual subjects, openBF’s solution show excellent agreement with the solutions from existing software. For reported simulations, openBF requires low computational times. Significance. openBF is easy to install, use, and deploy on multiple platforms and architectures, and gives accurate prediction of blood dynamics in short time-frames. It is actively maintained and available open-source on GitHub, which favours contributions from the biomechanical community.
17 November 2024 in International Journal of Computer Assisted Radiology and Surgery
Purpose: Accurately quantifying the rupture risk of unruptured intracranial aneurysms (UIAs) is crucial for guiding treatment decisions and remains an unmet clinical challenge. Computational Flow Dynamics and morphological measurements have been shown to differ between ruptured and unruptured aneurysms. It is not clear if these provide any additional information above routinely available clinical observations or not. Therefore, this study investigates whether incorporating image-derived features into the established PHASES score can improve the classification of aneurysm rupture status. Methods: A cross-sectional dataset of 170 patients (78 with ruptured aneurysm) was used. Computational fluid dynamics (CFD) and shape analysis were performed on patients’ images to extract additional features. These derived features were combined with PHASES variables to develop five ridge constrained logistic regression models for classifying the aneurysm rupture status. Correlation analysis and principal component analysis were employed for image-derived feature reduction. The dataset was split into training and validation subsets, and a ten-fold cross validation strategy with grid search optimisation and bootstrap resampling was adopted for determining the models’ coefficients. Models’ performances were evaluated using the area under the receiver operating characteristic curve (AUC). Results: The logistic regression model based solely on PHASES achieved AUC of 0.63. All models incorporating derived features from CFD and shape analysis demonstrated improved performance, reaching an AUC of 0.71. Non-sphericity index (shape variable) and maximum oscillatory shear index (CFD variable) were the strongest predictors of a ruptured status. Conclusion: This study demonstrates the benefits of integrating image-based fluid dynamics and shape analysis with clinical data for improving the classification accuracy of aneurysm rupture status. Further evaluation using longitudinal data is needed to assess the potential for clinical integration.
15 March 2023 in Frontiers in Cardiovascular Medicine
The treatment of ischaemic stroke increasingly relies upon endovascular procedures known as mechanical thrombectomy (MT), which consists in capturing and removing the clot with a catheter-guided stent while at the same time applying external aspiration with the aim of reducing haemodynamic loads during retrieval. However, uniform consensus on procedural parameters such as the use of balloon guide catheters (BGC) to provide proximal flow control, or the position of the aspiration catheter is still lacking. Ultimately the decision is left to the clinician performing the operation, and it is difficult to predict how these treatment options might influence clinical outcome. In this study we present a multiscale computational framework to simulate MT procedures. The developed framework can provide quantitative assessment of clinically relevant quantities such as flow in the retrieval path and can be used to find the optimal procedural parameters that are most likely to result in a favorable clinical outcome. The results show the advantage of using BGC during MT and indicate small differences between positioning the aspiration catheter in proximal or distal locations. The framework has significant potential for future expansions and applications to other surgical treatments.