Pyrolysis as a waste treatment method has gained relevance because it can generate higher value-added products in addition to reducing the environment’s secondary pollution. In this study, the catalytic pyrolysis of waste tires was evaluated using NiTiO3 and CoTiO3 ilmenites as catalysts and precursors of metal catalysts with the aim to produce an oil enriched in high-value hydrocarbons, such as benzene, toluene, a xylenes mixture, and products less-reported, such as p-cymene and p-cymenene. The experiments were performed in an analytical pyrolyzer coupled to GC/MS. The effect of the nature of the catalysts on the product distribution was compared with the uncatalyzed reaction. The main products of uncatalyzed pyrolysis were D, L-limonene (~60%), and isoprene (~25%) due to the depolymerization of natural rubber. Meanwhile, Ni-ilmenites-based catalysts favored the formation of target compounds to expense D, L-limonene. Moreover, the presence of metal in reduced-ilmenite sharply enhanced the selectivity by ~50% concerning oxidized ilmenite and above 80% compared to the uncatalyzed reaction for p-cymene and p-cymenene. By contrast, the Co-ilmenites-based catalysts showed a marginal effect on secondary reactions. Finally, the feasibility of forming the aromatic terpenes, p-cymene, and p-cymenene from limonene in the non-catalytic pyrolysis was evaluated.
1 September 2020 in Materials Today Communications
Supported Pd-based catalysts have been widely applied in the hydrogenation of specific functional groups. Recent trends have focused on employing Pd-based heterogeneous catalysts supported on inorganic nanotubes, wherein inner surface functionalization modulates both palladium nanoparticle (Pd-NP) dispersion and the interaction between reactants and the catalyst surface, thereby influencing catalytic properties. This study aims to develop a catalytic system using amine-lumened halloysite nanotubes immobilizing Pd-NPs (Pd/HNTA) as catalysts for hydrogenation reactions. The formation of Pd-NPs within the organo-functionalized lumen—modified by 3-aminopropyltrimethoxysilane—is confirmed by transmission electron microscopy (TEM) imaging, which reveals a particle size of 2.2 ± 0.4 nm. For comparison, Pd-NPs supported on pristine halloysite (Pd/HNTP) were used as control catalysts, displaying a metal particle size of 2.8 ± 0.8 nm and thereby demonstrating the effect of organic functionalization on the halloysite nanotubes. Both catalysts were employed in the hydrogenation of furfural (FUR) and nitrobenzene (NB) as model reactions. Pd/HNTA demonstrated superior catalytic performance for both substrates, with TOF values of 880 h−1 for FUR and 946 h−1 for NB, and selectivities exceeding 98% for tetrahydrofurfuryl alcohol (THFOH) and aniline (AN), respectively. However, recyclability studies displayed that Pd/HNTA was deactivated at the 10 catalytic cycles during the hydrogenation of FUR, whereas, in the hydrogenation of NB, 5 catalytic cycles were achieved with maximum conversion and selectivity at 360 min. These results revealed that the liquid-phase environment plays a pivotal role in catalyst stability. In the hydrogenation of NB, the coproduction of H2O adversely affects the interaction between the Pd particles and the inner amine-modified surface, increasing the deactivation of the catalyst with reuse. Thus, the Pd/HNTA catalyst holds significant promise for the development of noble-metal-based catalysts and their application in the transformation of other reducible organic functional groups via hydrogenation reaction.
The search for active, inexpensive, and stable heterogeneous catalysts to produce desired imines in fine chemistry presents an ongoing challenge for both academia and industry. This work reports the utilization of Co nanoparticles supported on TiO2 derived from the H2-assisted reduction of the perovskite-type mixed oxide CoTiO3. The entire preparation process is operationally simple and straightforward, enabling scalability for practical applications. The resulting catalyst comprises metallic cobalt nanoparticles responsible for the hydrogenation process, whereas the TiOx thin layer surrounding the cobalt promotes the adsorption of C=O, thereby enhancing the formation of desired products. Notably, at lower temperatures, the reaction yields the target imine product. Our study demonstrates a synergistic effect between nitrobenzene and benzaldehyde in the presence of a Co-TiOx interface, which reduces the apparent activation energy for the hydrogenation of the-NO2 group. Furthermore, under moderate reaction conditions, the catalytic system offers applicability to various nitrobenzene compounds substituted at the 4-position and benzaldehyde, resulting in high yields of the corresponding imines with electron-density-donating substituent groups. Finally, the catalyst exhibits facile separation for subsequent reuse, displaying moderate stability with minimal selectivity for the desired product.