Electric discharge machine (EDM) or may be call electric spark machine is one of most important of cutting process or manufacturing process because it give high accurate dimension and can be product most complex shape. In this present material removal rate (MRR) and electrode wear rate (EWR) for tool steel AISI L2 was study. The input parametric for this process is current, pulse on time and pulse off time. Full factorial method is used to formulate machine parameters and find the optimal process parameters of electric spark. The result show that the MRR is increasing with increasing in current and pulse on time while EWR is decreasing when current and pulse on time is increase. The experimented and predicted values of this process are approximately equal.
1 February 2021 in IOP Conference Series: Materials Science and Engineering
Electric discharge machine is one of the most important non-traditional cutting processes conducted without contact between the workpiece and tool electrode. Each cutting process was associated with residual stresses, and these stresses are significant in determining life and product performance. This study aimed to determine the residual stress produced in the electric discharge machine (EDM) using the X-ray diffraction method. The used EDM parameters in this study are current Ip (10, 20, 30) A, pulse on-time Ton (50, 100, 150) μs, and pulse off-time Toff (6.5, 12,25) μs these parametric divided into 27 specimens. Full factorial was used to analyze the result using Minilab 17 software. The result showed that approximately between the experimentally and predict result. Also, the result illustrated that the residual stress was increasing with increases in each parametric EDM used. Maximum tensile residual stress is (838.86 Mpa) at a higher value of machine parameters, while the best residual stress achieved is compressive residual stress at low machine parameters, and it reaches 201 Mpa.
This study examined the material removal rate (MRR) affected by the variables of the electrochemical process including electrode type, voltage, electrolyte type, electrolyte concentration, and gap. Titanium alloy was employed as the workpiece, while copper was utilized as the cylindrical electrode. The input parameters were established according to Taguchi’s methodology. An analysis of variance (ANOVA) using a linear regression model was dependent on making sense of the experiment’s findings. the solid electrode achieved the maximum material removal rate (MRR) value (0.0857) g/min, while the hollow electrode with (1500 l/hour) flow rate achieved the minimum material removal rate (MRR) value (0.00002) g/min. the material removal rate (MRR) was directly proportional to the voltage. Maximum material removal rate (MRR) occurred at a concentration of (75 g/l) for the (NH4C) electrolyte, while minimum material removal rate (MRR) occurred at a concentration of (50 g/l) for the (NH4Cl) electrolyte. It has been observed that the contributing factors in controlling material removal rate (MRR) were as follows; (66.67%) for the voltage, (5.89%) for the electrode, (5.72%) for the electrolyte concentration, (3.24%) for the type of electrolyte, and (3.07%) for the gap.
4 September 2018 in Al-Khwarizmi Engineering Journal
This paper is focused on studying the effect of cutting parameters (spindle speed, feed and depth of cut) on the response (temperature and tool life) during turning process. The inserts used in this study are carbide inserts coated with TiAlN (Titanum, Aluminium and Nitride) for machining a shaft of stainless steel 316L. Finite difference method was used to find the temperature distribution. The experimental results were done using infrared camera while the simulation process was performed using Matlab software package. The results showed that the maximum difference between the experimental and simulation results was equal to 19.3 , so, a good agreement between the experimental and simulation results was achieved. Tool life was decreased when spindle speed and feed were increased.
CNC machines have become an important component in the development of the manufacturing process. Wireless technologies can support all industrial needs as well as provide cost-effective solutions by connecting CNC machines to a wireless controller that allows the user to sit on a computer to send data to various locations without using any wire to control and teleoperate the CNC machines and monitor them remotely. This research focuses on the operation and remote control of CNC machines for machining of mechanical parts through the design and implementation of a wireless system through which a computer equipped with appropriate design and simulation software transmits the required data to the router, which in turn transmits the operating data to the control unit of the CNC machines. While a digital camera monitors the operation and broadcasts the real-time virtual scenes of the implementation to monitor the operation. In practical application, we used the UGNX program to implement the initial design of the parts to be machined, as well as to generate the required tool path and the simulation. While we used a CNC lathe type LabVolt to receive the data and machining the parts while a digital camera was connected to monitor the machining process.
25 August 2020 in Engineering and Technology Journal