Polychronis Dellis

Dr. Polychronis Dellis

orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2004 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
PDPolychronis Dellis
Polychronis Dellis
CAC Arcoumanis
C Arcoumanis
The onset and development of cavitation in the lubrication film present throughout the stroke between the piston ring and the cylinder liner in a reciprocating test rig was visualized by a charge-coupled device (CCD) camera and monitored by a miniature pressure sensor. Various transient cavitation patterns were identified during the stroke, ranging from developing fern-shaped cavities to string cavities extending gradually up to the trailing edge of the piston ring. Both the onset and the development of these cavities seem to be affected by piston speed and load; at higher speeds cavities appear later in the stroke and are larger in size, while at higher loads they appear earlier, are more numerous and, thus, smaller in size.

17 March 2010 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
PDPolychronis Dellis
Polychronis Dellis
Efficient engine operation is combined with effective lubrication in the ring/cylinder interface. On the one hand, there should be enough lubricant on the surfaces and, on the other hand, the lubricant contribution to combustion and, thus, to hydrocarbons and particulate emissions should be minimized. These requirements present a challenge to formulate new additives that would enable the lubricant to operate in the demanding circumstances inside the internal combustion engine and at the same time contribute to an environmentally friendly operation. This study is focused on parametric friction force measurements, their appearance close to the dead centres of the stroke, and how load, speed, and temperature affect the friction maxima. An approach is also attempted to the role of high-temperature, high-shear viscosity for a group of CASTROL lubricants. Piston rings with different curvatures were also tested, and friction power losses for each testing case are presented.

11 April 2012 in International Journal of Engine Research
Verified
Journal Article
Closed access
PDF file
PDPolychronis Dellis
Polychronis Dellis
CAConstantine Arcoumanis
Constantine Arcoumanis
Oil film pressure, the driving force behind piston-ring lubrication phenomena, is measured in a single piston-ring simulating rig after the successful installation of a miniature pressure transducer. The partition of overall load-carrying capacity between direct surface interaction and hydrodynamic action is clearly of some significance if the characteristics of the piston seal are to be understood and predicted with any confidence. It is therefore important that the contribution of the fluid film lubrication to load support be adequately represented. This study presents an extensive load, speed, temperature and piston-ring curvature parametric study on how the measured pressure profile at mid-stroke is affected in terms of peak pressure, magnitude and shift in the trailing edge of the piston ring, taking into account cavitation appearance and lubricant viscosity variation.

14 January 2019 in International Journal of Engine Research
Verified
Journal Article
Closed access
PDPolychronis Dellis
Polychronis Dellis
The laser-induced fluorescence technique is based on the excitation of molecules of a fluorescent material by a light source. The main advantage of this technique is that it has the potential to quantify the lubricant film thickness throughout the cycle. Similar to all the other optical techniques, it has this major advantage compared to the electrical techniques where the oil film can be measured only under the piston rings. In this work, experimental data from a simulating single-ring test rig are presented and further parametric analysis is given regarding cavitation in lubricants that was, at first, in the case of the single-ring test rig, evident in laser-induced fluorescence measurements. Different lubricants are used for the laser-induced fluorescence experiments and the different laser-induced fluorescence signals are analysed and interpreted compared to their physical and chemical properties and, furthermore, with the aid of imaging through a glass liner, a clearer picture is given regarding the cavitation shapes together with the respective laser-induced fluorescence measurements and cavitation initiation.

10 June 2019 in International Journal of Structural Integrity
Verified
Journal Article
Closed access
PDPolychronis Dellis
Polychronis Dellis
Purpose: Cavitation in piston-ring lubrication is studied as part of the performance of piston-ring assemblies. Cavitation degrades performance in engineering applications and its effect is that it alters the oil film pressure, generated at the converging-diverging wedge of the interface. Studies tried to shed light to the phenomenon of cavitation and compare it with cavities that have been identified in bearings. The paper aims to discuss this issue. Design/methodology/approach: Lubricant formulations were used for parametric study of oil film thickness (OFT) and friction providing the OFT throughout the stroke and LIF for OFT point measurements. Lubricant formulation affects cavitation appearance and behaviour when fully developed. Findings: Cavitation affects the ring load carrying capacity. Different forms of cavitation were identified and their shape and size (length and width) is dictated from reciprocating speed and viscosity of the lubricant. A clear picture is given from both techniques and friction results give quantifiable data in terms of the effect in wear and cavitation, depending on the lubricant properties. Research limitations/implications: Engine results are limited due to manufacturing difficulties of visualisation windows and oil starvation. Therefore, full stroke length sized windows were not an option and motoring tests were implemented due to materials limitations (adhesive and quartz windows). Lubricant manufacturer has to give data regarding the chemistry of the lubricants. Originality/value: The contribution of cavitation in piston-ring lubrication OFT, friction measurements and lubricant parameters that try to shed light to the different forms of cavitation. A link between viscosity, cavitation, shear thinning properties, OFT and friction is given.

6 June 2023 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
PDPolychronis Dellis
Polychronis Dellis
The lubricated interface at the piston-ring and liner and its interaction with different lubricants and testing conditions is examined in terms of experimental measurements that show the minimum oil film thickness developed at the lubricated or depending on conditions partly lubricated conjunction and the surface interaction intensity, as measured from the friction sensor. An analysis is carried out with the use of different parameters for the experiments as well as different lubricants in a simplified piston-ring simulation test rig. This analysis is further enhanced with the squeeze film effect investigations close to the stroke reversals and together with cavitation initiation and load-carrying effect results from previous experimental data, light is shed on the interacting surface’s behaviour at the different lubrication regimes. Another parameter, the viscosity index of the lubricant is used as an indication of the effects of squeeze film shift and friction force measurements and how the load and temperature effect are influencing the squeeze film.