This study experimentally assesses the thermal performance of a proposed phase change material (PCM)-based battery pack under elevated ambient temperatures. In addition, the novel approach of the research addresses scenarios where the ambient temperature reaches the PCM’s melting point while maintaining the initial temperature at the ideal operating point of 22 °C. The experiments employed nine 2500 mAh 18650 lithium-ion cells connected in series and subjected to constant-current discharges of 1C and 3C, with a conventional air-cooled system as the baseline and paraffin as the PCM. The results indicate that as the ambient temperature reached the PCM’s melting point, approximately 98% utilization of the PCM around the heating cell was achieved. Additionally, the PCM demonstrates noticeable advantages over the baseline by stabilizing the temperature profile and reducing the maximum temperature increase rate from over 18 °C in the baseline system to around 7 °C. Notably, under a high-load (3C) discharge rate, the PCM-based system successfully maintained battery temperatures below 42 °C, demonstrating its effectiveness under demanding operational scenarios. These findings establish a critical baseline for PCM-based BTMSs operating under elevated ambient temperatures and up to the melting point of the PCM, thereby informing future research and development of more efficient PCM-based thermal management solutions.
This study investigates incorporating a partial copper wire mesh within a phase change material (PCM)-based battery pack to enhance heat dissipation. Nine series-connected 21700 lithium-ion cells (5000 mAh) were discharged at 1C to 3C (5–15 A) at an ambient temperature of 22 °C. A thermodynamic energy balance framework quantified heat generation, dissipation, and latent heat utilization. Experimental results indicate that integrating the copper mesh significantly improved heat dissipation, lowered peak cell temperatures, and reduced latent utilization. Compared to the baseline pure-PCM hybrid system, the mesh-PCM configuration decreased maximum mean cell temperatures by 3.7, 2.6, and 4.8 ± 0.6 °C at 1C, 2C, and 3C discharge rates, respectively, while increasing heat dissipation by 20%–40%. However, a specific thermophysical design trade-off was observed at the 3C rate, where the spatial temperature non-uniformity increased from 1.2 to 1.8 ± 0.1 °C. At moderate discharge rates (1C and 2C), the mesh-PCM system effectively managed heat without requiring macroscopic latent heat utilization, while at 3C, the bulk PCM melting fraction was reduced from 15.3% to 9.9%. This extends safe operational limits up to 3C. These findings highlight the partial mesh integration to enhance the performance of PCM-based battery thermal management system, offering a lightweight and effective upgrade for conventional pure-PCM hybrid cooling methods.
This study presents a novel physics-based deep learning framework for assessing the spatiotemporal temperature distribution within a phase change material (PCM)-based battery pack. To accurately model the complex thermal dynamics, particularly extreme heat generation and steep temperature gradients at cell surfaces, a coupled Physics-Informed Neural Network (PINN) ensemble was developed. This core innovation entails the simultaneous training of six distinct PINNs, interconnected through a periodic knowledge transfer mechanism. This process ensures physical consistency across the operational spectrum, thereby guaranteeing that the learned thermal fields evolve intelligently with the discharge rate. Furthermore, the framework addresses the PCM Stefan problem using a physically consistent, enthalpy-based formulation augmented with Fourier feature mapping to capture sharp phase-change interfaces and high-frequency thermal dynamics. The system, comprising nine series-connected 21700 lithium-ion cells, was trained at discharge rates of 1C (5A) to a high-rate 6C (30A) under a controlled ambient temperature of 22 °C. Validation against sparse experimental sensor data demonstrated high predictive fidelity, with a root mean square error of less than 0.5 °C. Beyond internal temperatures, the model successfully reconstructed the heat flux boundary conditions at battery cells and copper pipe surfaces, confirming the validity of the learned thermal gradients. The trained network enabled the export of continuous 4D/3D/2D temperature and phase change contours, offering detailed whole-field visualization unattainable by sensors alone. Results indicate that while PCM provides effective thermal buffering, the melt fraction approaches 78% at 6C, highlighting the system's operational boundaries. This research establishes a coupled Physics-informed surrogate for the optimization of next-generation battery thermal management systems.