Stefanos Stefanos Gkatzogiannis

Dr. Stefanos Stefanos Gkatzogiannis

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in International Journal of Fatigue
Verified
Journal Article
Closed access
SGStefanos Stefanos Gkatzogiannis
Stefanos Stefanos Gkatzogiannis
JWJoscha Weinert
Joscha Weinert
IEImke Engelhardt
Imke Engelhardt
PKPeter Knoedel
Peter Knoedel
TUThomas Ummenhofer
Thomas Ummenhofer

1 May 2017 in Journal of Constructional Steel Research
Verified
Journal Article
Closed access
PKPeter Knoedel
Peter Knoedel
SGStefanos Stefanos Gkatzogiannis
Stefanos Stefanos Gkatzogiannis
TUThomas Ummenhofer
Thomas Ummenhofer

7 May 2020 in Welding in the World
Verified
Journal Article
Open access
PDF file
JSJan Schubnell
Jan Schubnell
ECEva Carl
Eva Carl
MFMajid Farajian
Majid Farajian
SGStefanos Stefanos Gkatzogiannis
Stefanos Stefanos Gkatzogiannis
PKPeter Knödel
Peter Knödel
HEHamdollah Eslami
Hamdollah Eslami
The induction of near-surface compressive residual stress is an important factor for fatigue life improvement of HFMI-treated welded joints. However, the relaxation of these beneficial residual stresses under single overload peaks under variable amplitude and service loads may significantly reduce fatigue life improvement. For this reason, several recommendations exist to limit the maximum applied load stress for this kind of post-treated welded joints. In this work, the effect of single tension and compression overloads on the relaxation behavior of HFMI-induced residual stresses was studied experimentally by means of X-ray and neutron diffraction techniques complemented by numerical simulation at transverse stiffeners made of mild S355J2 steel and high strength S960QL steel. Loads were applied close to the real yield strength of the base material. Significantly different relaxation behavior was observed for S355J2 and S960QL steel. Furthermore, high compression loads lead to full residual stress relaxation at the weld toe of S960QL and moderate relaxation for S355J2. High tension loads lead only to slight relaxation.

1 September 2016 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
PKPeter Knoedel
Peter Knoedel
SGStefanos Stefanos Gkatzogiannis
Stefanos Stefanos Gkatzogiannis
TUThomas Ummenhofer
Thomas Ummenhofer
One of the decisive criteria in the selection of material between steel and aluminium could be the welding RS (residual stresses), which play an important role for the fatigue behavior of the structures under cycling loading. In the current paper simulations in commercial FE software ANSYS were carried out, in order to calculate the welding RS field for three different materials: structural steel S355 and the aluminum grades EN AW-6060 and EN AW-5754. In the case of EN AW-6060 influence of recrystallization on the yield strength of the HAZ (heat affected zone) was taken into consideration.

13 September 2017 in ce/papers
Verified
Journal Article
Closed access
PDF file
SGStefanos Stefanos Gkatzogiannis
Stefanos Stefanos Gkatzogiannis
PKPeter Knoedel
Peter Knoedel
TUThomas Ummenhofer
Thomas Ummenhofer

16 September 2019 in ce/papers
Verified
Journal Article
Open access
PDF file
SGStefanos Stefanos Gkatzogiannis
Stefanos Stefanos Gkatzogiannis
PKPeter Knoedel
Peter Knoedel
TUThomas Ummenhofer
Thomas Ummenhofer
High Frequency Mechanical Impact treatment is investigated numerically in the present paper. A first‐step numerical dynamic analysis is carried out using the solver LS‐Dyna. The treatment of an unnotched component of S355 is simulated. The strain rate dependent material parameter Cowper‐Symonds is calibrated for the investigated material based on data from literature. Goal of the present analysis is to act a first step for a robust engineering approach, which will calculate with sufficient preciseness the residual stresses introduced by this post‐weld treatment. The calculated residual stresses of the present investigation are compared with respective measurements found in literature. Deviation between measured and simulated residual stresses indicates the need for further improvement of the present model.