Paulo Branco

Prof. Dr. Paulo Branco

University of Lisbon, Lisbon, Lisboa, Portugal
orcid

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2001 in IEEE Transactions on Aerospace and Electronic Systems
Verified
Journal Article
Closed access
FSF. Soares
F. Soares
Paulo BrancoPaulo Branco
Paulo Branco
A Matlab/Simulink environment to simulate a 6/4-switched reluctance motor is described. From its linear model to the nonlinear model, its dynamics is described and discussed in detail. All simulations are completely documented by their block diagrams and corresponding special Matlab functions and parameters quickly develop its model to the reader. Based on the developed model, simulation studies are performed and compared with measured motor phase currents either for hysteresis and voltage control strategies, and the steady-state motor operation to validate the model.

1 April 2010 in Applied Energy
Verified
Journal Article
Closed access
THT. Henriques
T. Henriques
BCB. César
B. César
Paulo BrancoPaulo Branco
Paulo Branco

1 February 2018 in Applied Energy
Verified
Journal Article
Closed access
ACAndré F.A. Castanheira
André F.A. Castanheira
João FernandesJoão Fernandes
João Fernandes
Paulo BrancoPaulo Branco
Paulo Branco


29 February 2016 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
João FernandesJoão Fernandes
João Fernandes
Paulo BrancoPaulo Branco
Paulo Branco
This paper analyzes the electromechanical characteristics of a novel shell-like spherical induction machine with multiple degrees-of-freedom (DOF), formed by a shell stator and a spherical hollow rotor. The shell-like induction machine is evaluated using n-harmonic analytical models for its electromechanical characteristics. The electromechanical model includes the distribution of the copper windings in the stator slots, incorporating the currents harmonic content to describe its spatial distribution. The distribution of the magnetic potential vector and the components of the magnetic flux density are computed using the real source-current distribution. A small prototype was built to validate the analytical model. To do so, experimental tests were done to the magnetic flux density and the torque. The shell-like induction motor is concretized as traction motor in an electric wheel-chair. Its results are compared with a finite-element analysis tool.

17 March 2011 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LHLuis Oscar de Araujo Porto Henriques
Luis Oscar de Araujo Porto Henriques
LRLuís Guilherme Barbosa Rolim
Luís Guilherme Barbosa Rolim
WSWalter Issamu Suemitsu
Walter Issamu Suemitsu
JDJ. A. Dente
J. A. Dente
Paulo BrancoPaulo Branco
Paulo Branco
Despite becoming competitive with ac and dc machines, the necessity for a shaft position transducer makes switched reluctance (SR) machines lose their low cost advantage, mainly as low power machines such as fans and pumps. Many techniques have been proposed for indirect rotor position detection for SR machines. However, their characteristics can be summed up as being based on a lookup table plus an interpolation algorithm, making them specific to a particular machine. For economic reasons and also dynamic performance, sensorless algorithms need a learning mechanism to allow them to adapt to a new SR machine or even adapt to changes in the SRM parameters. This paper presents a novel methodology for position sensor elimination for SR machines. Using the voltage from each conducting phase and the reference current signal as inputs, the rotor speed is first obtained as the output of a neurofuzzy learning system used as a “virtual” speed sensor. Then, the rotor position is determined by integrating the estimated value of speed. The effectiveness of the proposed sensorless technique was investigated through a series of real-time experiments on an SR drive system. The experimental results show that the suggested “virtual” speed sensor and corresponding rotor position can operate well in a sensorless SR speed control system.