Foysal Ahammed Mozumdar

Mr. Foysal Ahammed Mozumdar

Industrial and Production Engineering, Bangladesh University of Engineering and Technology, Dhaka, Bangladesh

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 December 2024 in Heliyon
Verified
Journal Article
Open access
TSTanhim Zaman Sheikh
Tanhim Zaman Sheikh
Foysal Ahammed MozumdarFoysal Ahammed Mozumdar
Foysal Ahammed Mozumdar
MKMd. Rezaul Karim
Md. Rezaul Karim
QAQumrul Ahsan
Qumrul Ahsan
The focus of this study was to investigate the potential of using waste materials like, waste glass powder and wood flour as fillers in polypropylene thermoplastic, and to assess their mechanical, morphological and thermal properties, as a means to add value to these wastes. Waste glass powder, with particle sizes of 125 μm, 63 μm, and 45 μm, was used as a filler material in the polypropylene matrix, along with wood flour particles of 250 μm in size. After identifying the optimal particle size (45 μm) sample, the WGP content was increased from 10 wt% to 15 wt% and 20 wt%. A four-step procedure was followed to create the composites, involving a kinetic mixer, sieve analysis, vacuum oven drying, and a compression molding machine. The results demonstrate that flexural strength and flexural modulus were highest in samples composed of 10 wt% and 15 wt% glass powder with a particle size of 45 μm. The tensile strength was highest in 100 wt% PP but the tensile modulus in 20 wt% glass powder with a 45 μm particle-sized sample. The maximum rebound hardness was also found in 100 wt% PP. The TGA results showed that 15 wt% WGP with a particle size of 45 μm sample was most thermally stable. A higher percentage (20 wt%) addition of waste glass powder caused non-uniform dispersion and the agglomeration of the fillers in the polymer matrix composite, which was visible in the microscopic analysis. This study found that the mechanical, morphological and thermal properties of the composite were improved by using finer particles and certain filler percentages.

1 November 2025 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
SFSynthia Ferdouse
Synthia Ferdouse
Foysal Ahammed MozumdarFoysal Ahammed Mozumdar
Foysal Ahammed Mozumdar
Zhong HuZhong Hu
Zhong Hu
The growing demand from the automotive industry for lightweight, high-performance, and advanced manufacturing techniques for efficient and cost-effective production has accelerated the adoption of fiber-reinforced polymer composites. However, considering the manufacturing complexity of these materials, design remains challenging due to the intricate and interdependent relationships between the process conditions, the part geometry, and the resulting microstructure and quality. This research utilized the Autodesk Moldflow Insight software to design an injection molding process for the manufacturing of discontinuous glass fiber-reinforced polymer parts through computer modeling. A geometrically complex car fender was used as a case study. The effects of various process parameters, particularly gate locations, on the injection-molded parts’ properties (such as the fiber orientation, volumetric shrinkage, and shear rate) were investigated. Multiple injection molding process configurations were designed and simulated, including three, four, and five gates at varying locations. Based on the optimal performance (i.e., low shrinkage, a consistent fiber orientation, and a controllable shear rate), an optimal configuration with four gates at appropriate locations (corresponding to the second gate location set) was identified based on multicriteria decision-making analysis, i.e., volumetric shrinkage of 8.5−2.2+1.4%, a fiber orientation tensor of 0.927 ± 0.011, and a stable shear rate < 74,324 (1/s). A reduced strain closure model (modified Folgar–Tucker model) was used to predict the glass fiber orientation. A multicriteria decision-making technique, based on similarity ranking with an ideal solution, was employed to optimize the gate location. The simulation results clearly demonstrate that the gate placement is crucial for material behavior during molding and for reducing common defects. The simulation-based injection molding process design for the manufacturing of discontinuous fiber-reinforced polymer parts proposed in this paper can improve the production efficiency, reduce trial-and-error rates, and improve part quality.