Ergün Guntekin

Prof. Dr. Ergün Guntekin


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 November 2023 in Turkish Journal of Forestry | Türkiye Ormancılık Dergisi
Verified
Journal Article
Open access
PDF file
EGErgün Guntekin
Ergün Guntekin
Elastic constants of Scots pine (Pinus sylvestris L.) wood grown in Turkey were investigated using non-destructive ultrasound tests. Elastic modulus in longitudinal and perpendicular directions (EL, ER, ET), shear modulus in principal planes (GLR, GLT, GRT) and Poisson ratios (ʋLR, ʋRL ʋLT, ʋLT, ʋRT, ʋTR) were calculated using cubic samples (20 mm) which were conditioned at 65 % relative humidity and 21 °C. Longitudinal and transverse ultrasonic sound velocities in fiber (L), radial (R) and tangential (T) directions were measured using 2.25 MHz and 1 MHz sensors, respectively. Transverse sound wave velocities at an angle of 45° to the L, R and T directions were also measured with a 1 MHz sensor in order to calculate the Poisson ratios. The predicted elastic modulus based on ultrasound in L, R, T directions were 10600, 1300 and 470 N/mm2, respectively. The predicted shear modulus based on ultrasound in LR, LT, RT planes were 1180, 1050 and 350 N/mm2, respectively. Poisson ratios varied between 0.04 to 0.95. Comparing the data available in the literature, elastic constants of scots pine determined using ultrasonic method were within the acceptable values.

28 March 2025 in Drvna industrija
Verified
Journal Article
Open access
PDF file
EGErgün Guntekin
Ergün Guntekin
MUMesut Uysal
Mesut Uysal
Sandwich panels composed of different core materials with plywood facings were analyzed using experimental and numerical methods. Particleboard (PB), fiberboard (MDF), and foam materials were used as the core of the sandwich, while beech plywood was laid as the only face material. The layers of the sandwich were adhered with polyurethane adhesive. Elasticities (E) of PB, MDF, and plywood were determined in the laboratory. The E value specified by the manufacturer for the foam was used to determine the flexural behavior of sandwich panels. Results of the study indicated that the type of core material significantly affects the bending behavior of sandwich panels with plywood facings. Sandwich panels with MDF-core were observed to be more resistant in bending compared to PB and foam-core sandwich panels. Core shear failure was the dominant failure type when wood-based materials were used as core material. Buckling or tension in facing was observed when foam was used as core material. The results of the study demonstrate that numerical models can be used to accurately predict the bending behavior of the sandwich panels until failure based on yield stress and tangent modulus of the materials.

6 February 2026 in Polymers
Verified
Journal Article
Open access
PDF file
SASebnem sevil ARPACI
Sebnem sevil ARPACI
EGErgün Guntekin
Ergün Guntekin
This study aims to optimize the physical, mechanical, and thermal properties of 100% Ground Granulated Blast Furnace Slag (GGBFS) based geopolymer wood-composite panels. Pine fibers were utilized as the primary reinforcement matrix, while glass and hemp fibers were introduced as secondary reinforcements at varying proportions (3%, 6%, 9% by weight). The research investigated the effects of fiber pretreatments (hot water vs. 1% NaOH) and reinforcement hybridization. Results indicate that GGBFS successfully geopolymerized, forming a hybrid N-A-S-H and C-A-S-H gel network. Quantitative analysis revealed that 9% glass fiber reinforcement yielded the highest mechanical performance, achieving a Modulus of Rupture (MOR) of 10.05 N/mm2 and Internal Bond (IB) strength of 1.32 N/mm2, alongside superior water resistance (1.0% Thickness Swelling). Conversely, while hemp fiber inclusion reduced mechanical strength (MOR: 5.77 N/mm2 at 9%), it significantly enhanced thermal insulation, reducing thermal conductivity to 0.10 W/m·K. It was observed that aggressive NaOH pretreatment caused alkali-induced degradation of pine fibers, negatively impacting the composite’s integrity compared to hot water treatment. This study demonstrates the feasibility of tailoring 100% slag-based geopolymer composites for either structural (glass-reinforced) or insulating (hemp-reinforced) applications using industrial by-products.

9 May 2024 in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
Verified
Journal Article
Closed access
EGErgün Guntekin
Ergün Guntekin
MUMesut Uysal
Mesut Uysal
Bu çalışmada, kontrplak kullanılarak güçlendirilmiş yongalevha ve MDF levhaların eğilme davranışı deneysel ve nümerik yöntemler ile incelenmiştir. Çalışmada 13 mm YL ve 12 mm MDF levhalar 4 mm kalınlığında kayın kontrplak kullanılarak güçlendirilmiştir. Levhaların yapıştırılmasında poliüretan tutkalı kullanılmıştır. Deney örnekleri 3 nokta eğilme testine tabi tutularak eğilme davranışları belirlenmiştir. Çalışmada test edilen güçlendirilmiş örneklerin sonlu elemanlar modelleri oluşturularak nümerik analizleri yapılmıştır. Çalışma sonuçları kontrplak kullanarak güçlendirilmiş yongalevha örneklerin eğilmede elastikiyet modülü ve eğilme direnci yükleme yönüne göre iki katına kadar, MDF örneklerinde ise %44 artmıştır. Güçlendirmenin etkinliği yükleme yönüne göre değişmektedir. Çekme gerilmesine maruz kalan yüzeylerin güçlendirilmesi basma gerilmesine maruz kalan yüzeylerin güçlendirilmesine göre eğilme özelliklerine daha fazla katkı yapmıştır. Eğilme testlerinden elde edilen yük-deformasyon eğrileri ile nümerik analizlerden elde edilen yük-deformasyon eğrilerinin çoğunlukla benzer olduğu görülmektedir. Çalışma sonuçları KP kullanılarak güçlendirilmiş YL ve MDF levhaların eğilme davranışlarının sonlu elemanlar yöntemi kullanarak tahmin edilebileceğini göstermiştir.

15 December 2022 in Bartın Orman Fakültesi Dergisi
Verified
Journal Article
Open access
PDF file
EGErgün Guntekin
Ergün Guntekin
Günümüzde kullanılan bilgisayar destekli tasarım ve üretim sistemlerinde ahşap malzemenin optimum tasarımının yapılabilmesi için tüm elastik sabitlerinin bilinmesi gerekir. Ortotropik bir malzeme olan ahşabın bu sistemlere entegrasyonu için dokuz elastik sabite ihtiyaç vardır. Bu çalışmada, Sedir (Cedrus libani A.) odununun sabit sıcaklık ve rutubet koşullarında elastik sabitleri incelenmiştir. Elastik sabitler basma testleri uygulanan 20 x 20 x 60 mm ebatlarındaki örneklerden elde edilmiştir. İncelenen özellikler; lif yönü, radyal ve teğet yönlerde elastik modülü (EL, ER, ET) üç ana düzlemde kayma modülü (GLR, GLT, GRT) ve altı Poisson oranından (νLR, νLT, νRL, νRT, νTL, νTR) oluşmaktadır. Deney örneklerinin üç farklı lif yönündeki basınç dirençleri de çalışmada belirlenmiştir. Yükleme sırasında meydana gelen şekil değişmeleri çift eksenli ekstansometre kullanılarak ölçülmüştür. Elastik sabitler, gerilme-şekil değiştirme eğrileri kullanılarak hesaplanmıştır. Sedir odununda belirlenen EL, ER, ET değerleri sırasıyla 7800, 890 ve 670 N/mm2, GLR, GLT, GRT değerleri ise sırasıyla 836, 780, 156 N/mm2 ve Poisson oranları ise 0.052 ile 0.522 arasında değişmektedir. Çalışmada bulunan elastik sabitler, sedir odununun nümerik modellenmesinde kullanılabilir.

29 December 2022 in Turkish Journal of Forestry | Türkiye Ormancılık Dergisi
Verified
Journal Article
Open access
PDF file
MTMuhammed Zakir Tufan
Muhammed Zakir Tufan
TATuğba YILMAZ AYDIN
Tuğba YILMAZ AYDIN
EGErgün Guntekin
Ergün Guntekin
BÜBirol Üner
Birol Üner
Bu çalışmada ısıl işlem görmüş Toros sediri (Cedrus libani A.Rich.) odunun bazı fiziksel ve kimyasal özellikleri araştırılmıştır. Isıl işlem, dört farklı sıcaklıkta (120, 150, 180 ve 210 °C) ve üç farklı zaman periyodunda (2, 5 ve 8 saat) gerçekleştirilmiştir. Elde edilen örneklerin kimyasal özellikleri FT-Infrared spektroskopi kullanılarak belirlenmiştir. Isıl işlem genellikle hücre duvarı, hemiselülozların parçalanması, indirgenmesi, uzun zincirli moleküllerin modifikasyonu ve odun içinde erişilebilir OH gruplarında değişiklikler meydana getirmektedir. Hidroksil guruplarında meydana gelen değişimler (H1429/897) belirlenmiş ve 8 saatlik ısıl işlem sonrası kristal yapı sırasıyla 1.21, 1.33, 1.25, 1.14 olarak belirlenmiştir. Selüloz zincirlerinde meydana gelen değişimler (A1370/670) pikinde tespit edilmiş ve kontrol örneği ile farklılıklar göstermiş olup dört farklı sıcaklıkta (120,150, 180 ve 210°C) ve 8 saatlik zaman periyodunda (3.13, 3.60, 3.33, 1.29) değerleri elde edilmiştir. Karbonil piklerinde 1740 nm dalga boyunda ısı ve zamana bağlı olarak artış görülmüştür. Buna göre en belirgin değişiklikler 8 saatlik işlem için 180 ve 210°C’ de gerçekleşmiştir.