This work reports the sustainable production of high-value-added products from biomass residues. Hierarchically porous carbons (HPCs) (micro/meso/macroporous) were obtained using the template-free route from bio-oil (biomass) pyrolysis and activation with zinc chloride in a single step. The materials obtained were characterized and applied to remove the following emerging contaminants 17α-ethinylestradiol, amoxicillin, ibuprofen, caffeine, and paracetamol from water. The hierarchically porous carbons presented high carbon contents (>80%), specific surface areas between 764 and 919 m2 g−1, and a multimodal pore size distribution (1 and 3.3 nm). The HPCs showed high thermal stability (>400 °C) and presence of nitrogen and oxygen groups on the surface such as ketones, phenols, ethers, pyrrolic-N and pyridinic-N. Preliminary adsorption contact tests showed removal rates above 70% for all contaminants studied. Adsorption isotherm studies demonstrated that most materials obtained qmax values of 188 mg g−1 and 310 mg g−1 for caffeine and paracetamol, respectively. Paracetamol exhibited a higher adsorption capacity when compared to caffeine. In addition, it was shown that the adsorption capacity of the material remained at 96% for caffeine and 85% for paracetamol until the tenth cycle. The increase in synthesis temperature has a direct influence on the textural parameters as well as surface chemistry, and can either alter or not the adsorption capacities, depending on the adsorption mechanisms involved. With this approach, we demonstrated the sustainable production of hierarchically porous carbons from biomass residues that have added value and can be used as adsorbents for emerging contaminants in water resources.
Bioactive glasses (BG) are promising materials for bone tissue engineering due to their bonding ability to biological tissues. In this study, a BG was synthesized via a modified sol–gel method that incorporated fumed silica. Two thermal treatments were applied: stabilization at 36.5 °C and calcination at 700 °C. X-ray diffraction analysis revealed the amorphous nature of BG stabilized at 36.5 °C, while calcination induced the formation of crystalline calcite. Nitrogen adsorption–desorption analysis revealed a specific surface area of 62 m2 g–1 for the stabilized BG, which decreased to 32 m2 g–1 after calcination. Thermogravimetric analysis indicated that the calcined sample exhibited lower thermal stability than the stabilized sample. Both BG samples exhibited the capacity to form a hydroxyapatite layer upon immersion in a simulated body fluid for a period of 48 h, being corroborated by X-ray diffraction, FTIR, and scanning electron microscopy. Additionally, cell viability assays with HaCaT keratinocytes showed enhanced cell proliferation compared to the control at 1, 4, and 7 days. A toothpaste containing 3 w/w% BG was also formulated with the calcinated sample and tested for dentin hypersensitivity, showing promising dentinal tubule occlusion, remineralization potential, and cytocompatibility. These results indicate that both samples prepared retains excellent surface properties, bioactivity, and cytocompatibility, even without high-temperature processing, highlighting its potential for biomedical applications.
1 January 2025 in Journal of the Brazilian Chemical Society
There is an increasing search for new sustainable materials, for example, the use of biomass for the production of carbon-rich materials. This review provides an overview on the synthesis of mesoporous carbon-based materials from biomass for applications in the adsorption of contaminants and capture of CO2. Pyrolysis is the most studied and easily scalable method for biomass-derived material production. However, this methodology typically leads to the formation of materials with lower pore order. On the other hand, template-based methodologies allow the synthesis of materials with greater mesopore ordering and a narrower pore size distribution. The materials have been applied to adsorb different contaminants such as dyes, heavy metals, pharmaceuticals and others, as well as CO2 capture. The literature extensively discusses the influence of surface area, pore size and the presence of functional groups. However, no results were found addressing the impact of pore ordering on these applications.