Mihai Costea

Mihai Costea

Auto-generated profile, based on publicly available information

Mihai Costea


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 October 2023 in Macromolecular Symposia
Verified
Journal Article
Closed access
MNMarian‐Sebastian Năstase
Marian‐Sebastian Năstase
MCMihai Costea
Mihai Costea
GJGabriel Jiga
Gabriel Jiga
TATudor George Alexandru
Tudor George Alexandru

5 August 2026 in Technologies
Verified
Journal Article
Open access
PDF file
MCMiruna Ciolca
Miruna Ciolca
SCSTOCHIOIU Constantin
STOCHIOIU Constantin
MCMihai Costea
Mihai Costea
APAlexandru Paraschiv
Alexandru Paraschiv
BFBaciu Florin
Baciu Florin
VDVlasceanu Daniel
Vlasceanu Daniel
Additive manufacturing enables the production of geometrically complex nickel-based superalloy components, but the high-temperature tensile response of selective laser-melted Inconel 718 remains strongly dependent on manufacturing route and build orientation. In this study, the tensile behavior of Inconel 718 specimens machined from wrought bar stock and fabricated by selective laser melting in horizontal and vertical build orientations was investigated at 23 °C, 450 °C, 550 °C and 750 °C. The experimental values were used in a finite element simulation to create a model that can accurately predict the mechanical behavior of IN718. The results show that the X-oriented SLM specimens exhibit tensile properties comparable to those of the wrought material, whereas the Z-oriented specimens display reduced strength and increased scatter, highlighting the effect of build orientation on mechanical performance. The numerical simulations reproduced the experimental stress–strain response with good agreement within the elastic and plastic deformation regimes, demonstrating the suitability of the proposed modeling approach for high-temperature structural assessment of Inconel 718 components manufactured by conventional and additive technologies.

1 January 2024 in International Journal of Modeling and Optimization
Verified
Journal Article
Open access
MCMihai Costea
Mihai Costea
GJGheorghe-Gabriel Jiga
Gheorghe-Gabriel Jiga

2 July 2026 in Macromolecular Symposia
Verified
Journal Article
Open access
MCMihai Costea
Mihai Costea
DTDaniela‐Ioana Tudose
Daniela‐Ioana Tudose
VTVirgil Tudose
Virgil Tudose
BSBogdan‐Nicolae Stoian
Bogdan‐Nicolae Stoian
MCMiruna Ciolca
Miruna Ciolca
This study presents a comparative investigation of the low‐velocity impact behavior of thin plates made from carbon fiber reinforced polymer (CFRP), polylactic acid (PLA), and acrylonitrile butadiene styrene (ABS). Plates with nominal thicknesses of 0.5 and 5 mm were subjected to standardized drop‐weight impact tests to evaluate their energy absorption capacity, failure modes, and structural response under dynamic loading. The experimental results indicate significant differences between the three materials: CFRP plates demonstrated superior impact resistance and energy absorption efficiency, attributed to their layered fiber structure and brittle failure behavior, while PLA specimens exhibited earlier failure through plastic deformation and crack propagation. The ABS specimens did not exhibit any visible cracks at an impact energy of 2 J, indicating a high capacity for plastic deformation without the immediate occurrence of cracking or fracture. To investigate the failure threshold of the material, the tests were repeated at an increased kinetic energy of 8 J. This step aimed to determine the failure mode and the upper energy absorption limit of the ABS material under intensified dynamic loading. The absorbed impact energy per unit thickness was analyzed to isolate and highlight the intrinsic material behavior, minimizing the influence of thickness variation. Finite element analysis models were developed to simulate the impact response of the tested specimens. The study provides valuable insights for material selection in the design of lightweight structures exposed to low‐velocity impact, with potential applications in aerospace, automotive, and consumer electronics industries.

5 July 2026 in Macromolecular Symposia
Verified
Journal Article
Closed access
MCMiruna Ciolca
Miruna Ciolca
SCSTOCHIOIU Constantin
STOCHIOIU Constantin
MCMihai Costea
Mihai Costea
BFBaciu Florin
Baciu Florin

2 July 2026 in Macromolecular Symposia
Verified
Journal Article
Open access
MCMihai Costea
Mihai Costea
MCMiruna Ciolca
Miruna Ciolca
BSBogdan‐Nicolae Stoian
Bogdan‐Nicolae Stoian
The study focuses on the experimental determination of the impact behavior of PLA components manufactured through additive manufacturing, where the infill density of each tested specimen is varied. The evaluation of the impact energy absorbed by each configuration provides relevant insights into the influence of internal structure on mechanical performance, thus contributing to the optimization of manufacturing parameters for the development of components that must respect the efficiency in terms of mechanical strength and material use. In this paper, the authors investigate the influence of internal structure on impact strength by proposing four different infill density configurations for 3D‐printed PLA specimens: 30%, 50%, 80%, and 100% infill. These variations were selected to provide a comprehensive understanding of how internal material volume increase affects the mechanical performances under impact loading. By systematically analyzing the absorbed impact energy for each configuration, the study aims to establish correlations between infill percentage and structural integrity, offering valuable insights for optimizing additive manufacturing parameters.