We report on an experimental investigation of the incubation effect during irradiation of stainless steel with bursts of ultrashort laser pulses. A series of birefringent crystals was used to split the pristine 650-fs pulses into bursts of up to 32 sub-pulses with time separations of 1.5 ps and 3 ps, respectively. The number of selected bursts was varied between 50 and 1600. The threshold fluence was measured in case of Burst Mode (BM) processing depending on the burst features, i.e. the number of sub-pulses and their separation time, and on the number of bursts. We found as many values of threshold fluence as the combinations of the number of bursts and of sub-pulses constituting the bursts set to give the same total number of impinging sub-pulses. However, existing incubation models developed for Normal Pulse Mode (NPM) return, for a given number of impinging pulses, a constant value of threshold fluence. Therefore, a dependence of the incubation coefficient with the burst features was hypothesized and experimentally investigated. Numerical solutions of the Two Temperature Model (TTM) in case of irradiation with single bursts of up to 4 sub-pulses have been performed to interpret the experimental results.

In numerous fields such as aerospace, the environment, and energy supply, ice generation and accretion represent a severe issue. For this reason, numerous methods have been developed for ice formation to be delayed and/or to inhibit ice adhesion to the substrates. Among them, laser micro/nanostructuring of surfaces aiming to obtain superhydrophobic behavior has been taken as a starting point for engineering substrates with anti-icing properties. In this review article, the key concept of surface wettability and its relationship with anti-icing is discussed. Furthermore, a comprehensive overview of the laser strategies to obtain superhydrophobic surfaces with anti-icing behavior is provided, from direct laser writing (DLW) to laser-induced periodic surface structuring (LIPSS), and direct laser interference patterning (DLIP). Micro-/nano-texturing of several materials is reviewed, from aluminum alloys to polymeric substrates.

Ice formation is a serious issue in many fields, from energy to aerospace, compromising the devices’ efficiency and security. Superhydrophobicity has been demonstrated to be correlated to the anti-icing properties of surfaces. However, fabricating surfaces with robust water repellence properties also at subzero temperature is still a great challenge. In this work, femtosecond laser (fs-laser) texturing is exploited to produce superhydrophobic surfaces with anti-icing properties on Al2024, an aluminum alloy of great interest in cold environments, in particular for aircraft production. Our textured substrates present self-cleaning properties and robust water repellency at subzero temperatures. Moreover, outstanding anti-icing properties are achieved on the textured surfaces at −20 °C, with water droplets bouncing off the surface before freezing.

The capability of isolating and sorting specific types of cells is crucial in life science, particularly for the early diagnosis of lethal diseases and monitoring of medical treatments. Among all the micro-fluidics techniques for cell sorting, inertial focusing combined with the laminar vortex technology is a powerful method to isolate cells from flowing samples in an efficient manner. This label-free method does not require any external force to be applied, and allows high throughput and continuous sample separation, thus offering a high filtration efficiency over a wide range of particle sizes. Although rather recent, this technology and its applications are rapidly growing, thanks to the development of new chip designs, the employment of new materials and microfabrication technologies. In this review, a comprehensive overview is provided on the most relevant works which employ inertial focusing and laminar vortex technology to sort particles. After briefly summarizing the other cells sorting techniques, highlighting their limitations, the physical mechanisms involved in particle trapping and sorting are described. Then, the materials and microfabrication methods used to implement this technology on miniaturized devices are illustrated. The most relevant evolution steps in the chips design are discussed, and their performances critically analyzed to suggest future developments of this technology.

We report on a one-step method for cutting 250-µm-thick quartz plates using highly focused ultrashort laser pulses with a duration of 200 fs and a wavelength of 1030 nm. We show that the repetition rate, the scan speed, the pulse overlap and the pulse energy directly influence the cutting process and quality. Therefore, a suitable choice of these parameters was necessary to get single-pass stealth dicing with neat and flat cut edges. The mechanism behind the stealth dicing process was ascribed to tensile stresses generated by the relaxation of the compressive stresses originated in the laser beam focal volume during irradiation in the bulk material. Such stresses produced micro-fractures whose controlled propagation along the laser beam path led to cutting of the samples.

Changing the wetting properties of surfaces is attracting great interest in many fields, in particular to achieve a surface with a superhydrophobic behavior. Laser machining is an emerging technique to functionalize materials with high precision and flexibility without any chemical treatment. However, when it is necessary to treat large area surfaces laser-based methods are still too slow to be exploited in industrial productions. In this work, we show that by improving the laser texture strategy it is possible to reduce the laser processing time to produce superhydrophobic aluminum alloy surfaces. Three different surface texture geometries were micromachined; namely, square, circular and triangular lattice grooves. We found that if the spacing between the grooves is narrow, i.e., when the percentage of the textured surface is high, the volume of air trapped inside the micromachined structures plays an important role in the wetting behavior. Meanwhile, when the groove spacing approaches the droplet dimensions, the texture geometry has a preponderant influence. Based on these findings an appropriate choice of the laser texture strategy allowed the fabrication of superhydrophobic aluminum alloy surfaces with a 10% reduction of processing time.