Radoslav N Tomović

Dr. Radoslav N Tomović

University of Montenegro, Podgorica, Montenegro
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2010 in International Journal of Mechanical Sciences
Verified
Journal Article
Closed access
Radoslav N TomovićRadoslav N Tomović
Radoslav N Tomović
VMVojislav Miltenovic
Vojislav Miltenovic
Milan BanicMilan Banic
Milan Banic
Aleksandar MiltenovićAleksandar Miltenović
Aleksandar Miltenović



1 May 2022 in Advanced Engineering Letters
Verified
Journal Article
Open access
Blaza StojanovićBlaza Stojanović
Blaza Stojanović
Radoslav N TomovićRadoslav N Tomović
Radoslav N Tomović
Sandra N GajevicSandra N Gajevic
Sandra N Gajevic
JPJelena Petrović
Jelena Petrović
Slavica MiladinovicSlavica Miladinovic
Slavica Miladinovic
In this paper is presented the tribological behavior of A356-based aluminum composites using Taguchi design. Testing of tribological characteristics of aluminum composites was done on a tribometer with block on disc contact geometry. Composite materials were obtained by compocasting. The orthogonal matrix L18 is used to form the experimental design using the Taguchi method. The tribological characteristics of the aluminum composite reinforced with SiC (A356/10 wt.% SiC) were compared to the base material A356 for three sliding speeds (0.25 m/s; 0.5 m/s and 1.0 m/s), three values of normal load (10 N, 20 N and 30 N) and sliding distance of 150 m under lubrication conditions. ANOVA analysis showed that the least wear has a composite material at a load of 10 N and at sliding speed of 0.25 m/s.

17 January 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Radoslav N TomovićRadoslav N Tomović
Radoslav N Tomović
In this paper, a simplified approach in the analysis of the varying compliance vibrations of a rolling bearing is presented. This approach analyses the generation of vibrations in relation to two boundary positions of the inner ring support on an even and an odd number of the rolling element of a bearing. In this paper, a mathematical model for the calculation of amplitude and frequency of vibrations of a rigid rotor in a rolling bearing is presented. The model is characterized by a big simplicity which makes it very convenient for a practical application. Based on the presented mathematical model a parametric analysis of the influence of the internal radial clearance, external radial load and the total number of rolling elements on the varying compliance vibrations of rolling bearing was conducted. These parameters are the most influential factors for generating varying compliance vibrations. The results of the parametric analysis demonstrate that with the proper choice of the size of the internal radial clearance and external radial load, the level of the varying compliance vibrations in a rolling bearing can be theoretically reduced to zero. This result opposes the opinion that varying compliance vibrations of rolling bearing cannot be avoided, even for geometrically ideally produced bearing.

3 October 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Radoslav N TomovićRadoslav N Tomović
Radoslav N Tomović
This paper presents a new model for calculation of load for the most loaded rolling element in a rolling bearing with internal radial clearance. The calculation is based on a so-called load factor. By multiplying this factor by the value of the external radial load, the load transferred by the most loaded rolling element of the bearing is obtained. The values of the load factor are shown in the tables and diagrams, which makes the model very suitable for practical use. The load factors are shown for a ball bearing as well as for a roller bearing. The model considers two support positions of the inner ring on an even and odd number of rolling elements. The new model was compared with the most commonly used models up to now. The results showed greater accuracy of the studied model.