Tsutomu Tsuboi

Dr. Tsutomu Tsuboi

Nagoya Electric Works Co. Ltd.
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2009
Verified
Conference Paper
Closed access
NANayef Alsindi
Nayef Alsindi
CDChunjie Duan
Chunjie Duan
JZJinyun Zhang
Jinyun Zhang
TTTsutomu Tsuboi
Tsutomu Tsuboi
Recently, Ultra Wideband (UWB) Time Of Arrival (ToA)-based localization in Wireless Sensor Networks (WSNs) have received considerable attention. For a typical WSN operating in indoor environments, the localization performance can be degraded considerably due to the existence of non-line-of-sight (NLOS) channel conditions between the sensor nodes. In these channel conditions the ranging accuracy is degraded due to the attenuation and/or loss of the Direct Path (DP) signal which ultimately imposes a positive bias on the ToA-based distance estimation. As a result there is a need for robust algorithms that have the capability to identify and mitigate those NLOS ranging conditions. In this paper, we propose a novel, low complexity wireless channel condition estimation algorithm that identifies the condition of the channel. Based on the estimated ToA and Received Signal Strength (RSS) the algorithm identifies the channel condition which can be either LOS, NLOS - DP available, or NLOS - DP not available. A channel measurement campaign was conducted in an office environment and the measurement results confirms the validity of our algorithm. To integrate our channel condition estimation into the localization schemes, we propose two weight assignment schemes which generate either a ldquosoft weightrdquo or a ldquohard weightrdquo. Simulation results show that our estimator has robust performance with success rate of 85%. The simulations also show that by taking advantage of the channel condition estimation, we are able to reduce the RMSE of the localization estimate by over 40%.

1 March 2020 in Case Studies on Transport Policy
Verified
Journal Article
Closed access
TTTsutomu Tsuboi
Tsutomu Tsuboi
NYNoriaki Yoshikawa
Noriaki Yoshikawa

1 June 2007
Verified
Conference Paper
Closed access
TTTsutomu Tsuboi
Tsutomu Tsuboi
JYJun Yamada
Jun Yamada
NYNaoki Yamauchi
Naoki Yamauchi
MNMichihiro Nakagawa
Michihiro Nakagawa
TMTetsuhiro Maruyama
Tetsuhiro Maruyama
This is the first study for inside vehicle wireless communication system design with UWB technology under WiMedia standard. At first, MATLAB simulator has been developed then calculated BER in AWGR channel model. And it is confirmed adequacy of channel model compared with IEEE simulation model. And wireless transmission characteristics are measured with the following? conditions such as receiver on top of dashboard and transmitter on rear sheet, center of trunk etc. Then test result of BER and PER are compared with simulation model above those conditions. In case of wireless communication system design under IEEE802.15.3a and or WiMedia model with target 8% PER condition, inside vehicle wireless communication is capable for 3dB link margin for wireless communication with tweaking antenna gain and receiving NF for inside Vehicle communication system.

1 December 2008
Verified
Conference Paper
Closed access
TTTsutomu Tsuboi
Tsutomu Tsuboi
JYJun Yamada
Jun Yamada
NYNaoki Yamauchi
Naoki Yamauchi
MHMasato Hayashi
Masato Hayashi
This is the first study and field test analysis for DSRC (Dedicated Short distance Radio System) Vehicle wireless communication system design with first prototype developed WAVE (Wireless Access in Vehicle Environment) system platform in which IEEE802.11p and IEEE1609 standard software have been implemented. In the field test, packet reach ability as one of parameter for system evaluation has been measured for both WAVE announce frame and IP packet data between On-Board-Unit (OBU) and Road-Side-Unit (RSU). After basic WAVE functional test, it has been considered about safety application with this new DSRC technology and it is also evaluated in the field testing for informing road singe and camera steaming information transmission to vehicle. In this field testing, it is compared between single receiver concept in IEEE802.11p and dual receiver concept in Car to Car Communication Consortium (C2C-CC). Under the current existing IEEE802.11p specification, there are two types of communication channels i.e. Control Channel (CCH) and Service Channel (SCH). Those channels are sending during each 50 msec interval. The CCH is used for emergency information transmission basically and SHC is used for non- critical information such as video transmission for customer usage. Therefore it should be considered about time critical for sending CCH information. So it has been measured timing for each CCH and SCH frame arrival from RSU to OBU in real field testing as basic WAVE system functions.

1 October 2009
Verified
Conference Paper
Closed access
TTTsutomu Tsuboi
Tsutomu Tsuboi
JYJun Yamada
Jun Yamada
NYNaoki Yamauchi
Naoki Yamauchi
MNMichihiro Nakagawa
Michihiro Nakagawa
TMTetsuhiro Maruyama
Tetsuhiro Maruyama
This is the following paper after the first study for inside vehicle wireless communication system design with UWB (ultrawideband) technology which was presented in ITST 2007. In this paper, it is descried why UWB technology will be good for intra vehicle wireless communications and provides more detail UWB propagation analysis. Then multipath environment model intra vehicle is created in addition existing UWB simulation model. Wireless communication gain loss of intra vehicle multipath environment becomes around 4 dB degradation against AWGN (adaptive white Gaussian noise) based on several multipath gain loss simulations to identify intra vehicle environment effect in this paper. According to this multipath gain loss analysis, UWB technology is capable high speed wireless communication intra vehicle environments with 4 dB gain loss against AWGN. These analyses suggest technology challenges for intra vehicle wireless communication how to improve from WiMeida specification UWB to Intra vehicle UWB.

8 March 2021 in Infrastructures
Verified
Journal Article
Open access
PDF file
TTTsutomu Tsuboi
Tsutomu Tsuboi
The paper takes an analysis of traffic conditions in a developing country, namely, India. India is a country with a rapidly growing economy and a large market, and it has the second largest population in the world, which was 1.3 billion in 2018. India also suffers from environmental problems, such as air pollution and global warming that is contributed by traffic CO2 emissions from transportation. In order to analyze this problem, a particularly challenging issue in developing countries like India, is the collection of traffic data. In general, developing countries do not often have well established infrastructure such as installations of small traffic signals, they lack new road construction and public transportation, etc. This study is the first real traffic congestion analysis in India and introduces unique traffic flow analysis such as: (1) Collecting over a month of recent traffic data in a major city in India, (2) defining traffic congestion from occupancy parameter based on traffic flow theory and observation data, and (3) using geographical special analysis (GIS) for identifying traffic congestion location. These three combination analysis enables one to identify the most congested area in the city with quantitative congestion condition. This study becomes useful to other countries that have similar issues.