Plamen Punov

Prof. Dr. Plamen Punov

Combustion engines, automobiles and transports, Technical University of Sofia, Sofia, Sofia-Grad, Bulgaria
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 June 2021 in Electronics
Verified
Journal Article
Open access
PDF file
Nikolay HinovNikolay Hinov
Nikolay Hinov
Plamen PunovPlamen Punov
Plamen Punov
Bogdan GilevBogdan Gilev
Bogdan Gilev
Gergana VachevaGergana Vacheva
Gergana Vacheva
This paper presents a numerical study of the effect of the transmission configuration on the energy consumption of an electric vehicle. The first part of this study is related to a vehicle simulation model that takes into consideration vehicle resistances such as aerodynamic, rolling and inertial resistance as well as the traction force. The model was then validated by means of vehicle acceleration time, from 0 to 100 km/h in the case of a single-speed gearbox. Vehicle power demand and electrical energy consumption were then evaluated over three standardized test cycles: WLTC-Class 3, NEDC and FTP-75. For each cycle, two cases were studied: a single-speed and dual-speed gearbox. Very different power demand was observed between the cycles in terms of maximum and average driving power. The most power-demanding cycle was WLTC, while NEDC was less power demanding. However, the specific driving energy per kilometer was very similar for NEDC and FTP-75, as it respectively accounted to 0.118/0.116 kWh/km and 0.117/0.115 kWh/km. WLTC led to a higher specific consumption of 0.127/0.124 kWh/km. A dual-speed gearbox led to better efficiency, within the range of 1.7% to 2.4%. The higher value was obtained for highly dynamic WLTC.

11 November 2016 in International Journal of Energy Research
Verified
Journal Article
Closed access
PDF file
Plamen PunovPlamen Punov
Plamen Punov
TETeodossi Evtimov
Teodossi Evtimov
RCRadu Chiriac
Radu Chiriac
Adrian Constantin ClenciAdrian Constantin Clenci
Adrian Constantin Clenci
QDQuentin Danel
Quentin Danel
GDGeorges Descombes
Georges Descombes

1 June 2021 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
Plamen PunovPlamen Punov
Plamen Punov
TGTsvetomir Gechev
Tsvetomir Gechev

31 March 2015 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Open access
Plamen PunovPlamen Punov
Plamen Punov
SLStéphanie Lacour
Stéphanie Lacour
CPChristelle Périlhon
Christelle Périlhon
PPPierre Podevin
Pierre Podevin
GDGeorges Descombes
Georges Descombes
TETeodossi Evtimov
Teodossi Evtimov
The paper presents an analysis of the possibilities of exhaust gas heat recovery for a tractor engine with an output power of 110 kW. On the basis of a literature review, the Rankine cycle seems to be the most effective way to recover the exhaust gas energy. This approach reduces the fuel consumption and allows engines to meet future restrictions on carbon dioxide emissions. A simulation model of the engine by means of a one-dimensional approach and a zero-dimensional approach was built into the simulation code AVL BOOST, and a model of the Rankine cycle was implemented. The experimental values of the effective power of the engine, the mass flow and the exhaust gas temperature were used to validate the engine model. The energy balance of the engine shows that more than 28.9% of the fuel energy is rejected by exhaust gases. Using the engine model, the energy and the exergy of the exhaust gases were studied. An experimental study of the real working cycle of a tractor engine revealed that the engine operates most of the time at a constant speed (n = 1650 r/min) and a constant load (brake mean effective pressure, 10 bar). Finally, Rankine cycle simulations with four working fluids were carried out at the most typical operating point of the engine. The simulation results reveal that the output power of the engine and the efficiency of the engine increase within the range 3.9–7.5%. The highest value was achieved with water as the working fluid while the lowest value was obtained with the organic fluid R134a. The power obtained with water as the working fluid was 6.69 kW, which corresponds to a Rankine cycle efficiency of 15.8%. The results show good prospects for further development of the Rankine cycle.

21 November 2018 in MATEC Web of Conferences
Verified
Journal Article
Open access
Plamen PunovPlamen Punov
Plamen Punov
TGTsvetomir Gechev
Tsvetomir Gechev
SMSvetoslav Mihalkov
Svetoslav Mihalkov
PPPierre Podevin
Pierre Podevin
DBDalibor Barta
Dalibor Barta
The pilot injection strategy is a widely used approach for reducing the noise of the combustion process in direct injection diesel engines. In the last generation of automotive diesel engines up to several pilot injections could occur to better control the rate of heat release (ROHR) in the cylinder as well as the pollutant formation. However, determination of the timing and duration for each pilot injection needs to be precisely optimised. In this paper an experimental study of the pilot injection strategy was conducted on a direct injection diesel engine. Single and double pilot injection strategy was studied. The engine rated power is 100 kW at 4000 rpm while the rated torque is 320 Nm at 2000 rpm. An engine operating point determined by the rotation speed of 1400 rpm and torque of 100 Nm was chosen. The pilot and pre-injection timing was widely varied in order to study the influence on the combustion process as well as on the fuel consumption.

7 November 2017 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
IDIvan Dobrev
Ivan Dobrev
FMFawaz Massouh
Fawaz Massouh
ADAmélie Danlos
Amélie Danlos
MTMichael Todorov
Michael Todorov
Plamen PunovPlamen Punov
Plamen Punov
This paper presents the aerodynamic study of a small car, which participated in Shell Ecomarathon Europe competition in the Urban Concept Hydrogen class. The goal is to understand the flow field around the vehicle. First, the flow is studied numerically using computational aerodynamics. The numerical simulation is carried out by means of CFD Fluent in order to obtain the drag force experienced by the vehicle and also the flow field. Then the flow field around the car is studied in a wind tunnel by means of particle image velocimetry (PIV). The comparison of the flow fields obtained numerically and experimentally shows good correspondence. The obtained results are very helpful for future car development and permit to improve the drag and to obtain a good stability.