This study shows the effect of the incorporation of natural fique fibers in a matrix formed by low-density polyethylene and aluminum (LDPE-Al) obtained in the recycling process of long-life Tetra Pak packaging. The reinforcement content was 10, 20, and 30% fibers, manufactured by hot-press compression molding of composite boards (LDPE-Al/fique). From the thermogravimetric analysis (TGA) it was determined that the proportions of the LDPE-Al were 75 : 25 w/w. Likewise, it was found that the aluminum particles increased the rigidity of the LDPE-Al, reducing the impact strength compared to LDPE recycled from Tetra Pak without aluminum; besides this, the crystallinity in the LDPE-Al increased with the presence of aluminum, which was observed by differential scanning calorimetry (DSC). The maximum strength and Young’s modulus to tensile and flexural properties increased with the incorporation of the fibers, this increase being a direct function of the amount of reinforcement contained in the material. Finally, a reduction in the density of the compound by the generation of voids at the interface between the LDPE-Al and fique fibers was identified, and there was also a greater water absorption due to weak interphase fiber-matrix and the hydrophilic fibers contained in the material.
This work presents the physical-thermal and mechanical characterization of a low-density polyethylene (LDPE)-Al matrix composite material that was obtained from reinforcing recycled (post-consumer) long-life Tetra Pak packages with fique natural fibers from southwestern Colombia. The fique was subjected to three chemical treatments to modify its surface (alkalinization, silanization and pre-impregnation with polyethylene) to increase the quality of its interfaces. Additionally, panels with 10%, 20%, and 30% v/v of fiber were manufactured by the hot compression molding. The mechanical properties of the different composite materials showed that the pre-impregnation treatment promoted a significant increase in the tensile and flexural properties with respect to the fiber-reinforced composite without surface modification. Additionally, in materials with 30% fibers that were treated with pre-impregnation, there was a decrease in the water absorption capacity of 53.15% when compared to composites made with 30% native fibers. Finally, increases in the fiber content mainly caused better mechanical performances, which increased as a direct function of the amount of fique incorporated.
Multiwall carbon nanotubes (MWCNTs) previously treated with a cationic polymer were incorporated on the surface of carbon fibers modified by three different chemical treatments, namely, oxidation, oxidation-silanization and oxidation-pre-impregnation. Prior to the incorporation of the MWCNTs, the physical surface properties of the fibers were studied by contact angle and the chemical surface properties by X-ray photoelectron spectroscopy (XPS). The interfacial shear strength (IFSS) of the different systems carbon fiber-MWCNTs-matrix was evaluated using the single-fiber fragmentation test (SFFT) and it was observed that the IFSS of the oxidized-pre-impregnated fibers, was considerably higher than that observed for the other fiber-matrix systems. This was attributed to enhanced interfacial interactions because the fiber surface treatments improved the wettability of the carbon fiber and the MWCNTs, which resulted in a better fiber-matrix mechanical interlocking and to the formation of covalent bonds between the different phases of the composite
In light of globalization and escalating environmental concerns, society is increasingly confronted with the challenge of implementing the concept of a circular economy, which promotes the recycle of waste materials and offers a promising solution. Aluminum dross, a byproduct of the aluminum production process, poses environmental issues when not properly managed. Therefore, this study examined the technical and financial feasibility of implementing an industrial process for the recovery and transformation of aluminum dross into raw materials for use in cementitious materials. From a technical perspective, two processes were evaluated: washing and the grindability of the material. An X-ray diffraction analysis allowed to verify an approximately 88% reduction in AlN (a compound that produces ammonia gases when reacting with water) after washing the material. The most efficient grinding process was achieved using an impact mill. The financial feasibility study was carried out through cash flow forecasting, which revealed that a minimum selling price of USD 0.12 per kilogram of processed material could generate a return rate of 9.7% over a five-year period. These results present opportunities for the metal and construction industries to develop products with low CO2 emissions by reintegrating aluminum dross into a productive cycle. Moreover, this work serves as a valuable reference for policymakers and environmental authorities seeking to formulate new legislation or incentives that encourage companies to invest in environmentally focused projects.
Biocomposites were prepared from a ternary matrix of polylactic acid (PLA), polycaprolactone (PCL), and thermoplastic starch (TPS) and reinforced with native fique fibers from southwestern Colombia. The influence of surface modification by alkalization of fique fibers on the interfacial properties of the biocomposite was studied using pull-out tests. Additionally, the effect of short fique fibers in three proportions (10%, 20%, and 30% (w/w)) on the tensile mechanical properties of the composite was evaluated. The experimental results indicated that the interfacial shear strength (IFSS) of the ternary matrix was predominantly influenced by PCL and characterized by the development of a weak interface that failed due to matrix yielding. Furthermore, the incorporation of short fique fibers increased the elastic modulus of the composite to values similar to those estimated with the Tsai–Pagano model. The alkalization treatment of the fique fibers improved the interface with the composite matrix, and this phenomenon was evidenced by the results of the micromechanical and tensile characterizations of the composite.
Although the use of primary aluminum dross as cement replacement has shown promising results in mortars and concretes, there is a knowledge gap between the effect of the secondary dross inactivation process and particle sizes on the mechanical properties and consistency. So, by using X-ray diffraction, laser granulometry, and scanning electron microscopy, this article describes first the inactivation process applied to a secondary aluminum dross. Second, this manuscript presents the fresh and hardened properties of mortar mixes containing 5, 10, and 20% inactivated secondary aluminum dross with three different particle sizes (i.e., fine, intermediate, and coarse). Mortar flow test results indicate that compressive and flexural strengths of mixes containing up to 20% fine and intermediate aluminum dross as cement replacement were satisfactory, respectively. These results have the potential to reduce the environmental and health impacts caused by cement production and secondary aluminum dross disposal, respectively. Moreover, the durability aspects of the mortar mixes, as well as the effectivity of the investigated inactivation process, are identified as future research topics.