Fabrice Giuliani

Dr. Fabrice Giuliani

Combustion Bay One e.U.
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2002 in Proceedings of the Combustion Institute
Verified
Journal Article
Closed access
Fabrice GiulianiFabrice Giuliani
Fabrice Giuliani
PGPierre Gajan
Pierre Gajan
ODOlaf Diers
Olaf Diers
MLMichel Ledoux
Michel Ledoux

1 March 2013 in Combustion and Flame
Verified
Journal Article
Closed access
TLThomas Leitgeb
Thomas Leitgeb
TSThierry Schuller
Thierry Schuller
DDDaniel Durox
Daniel Durox
Fabrice GiulianiFabrice Giuliani
Fabrice Giuliani
SKStefan Köberl
Stefan Köberl
Jakob WoisetschlägerJakob Woisetschläger
Jakob Woisetschläger

9 February 2010 in Measurement Science and Technology
Verified
Journal Article
Closed access
SKS Köberl
S Köberl
FFF Fontaneto
F Fontaneto
Fabrice GiulianiFabrice Giuliani
Fabrice Giuliani
Jakob WoisetschlägerJakob Woisetschläger
Jakob Woisetschläger

3 December 2009 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
Fabrice GiulianiFabrice Giuliani
Fabrice Giuliani
TLThomas Leitgeb
Thomas Leitgeb
ALAndreas Lang
Andreas Lang
Jakob WoisetschlägerJakob Woisetschläger
Jakob Woisetschläger
Laser vibrometry (LV) is originally a laser-based, line-of-sight measurement technique dedicated to the analysis of surface vibrations. It was lately adapted at TU Graz for monitoring the stability of an air-methane flame (Giuliani, et al., 2006, ASME Turbo Expo, ASME Paper No. GT2006-90413). This paper reports on the mapping of density fluctuations measured with LV in a premixed air-methane flame (free jet; swirl stabilized) with a forced flow modulation (quarter-wave resonator; amplification with a siren). In order to correlate the density fluctuations with the jet aerodynamics and turbulent flame shape, stereoscopic particle image velocimetry and high-speed schlieren visualizations were used. This paper addresses issues regarding the estimate of density fluctuations, the transform from line-of-sight to local measurement with tomographic methods, and the potential of the method for detailed description of thermoacoustic couplings. One emphasized application of LV is its ability to perform precise and low-cost benchmark stability tests on a combustor during the design phase (time-resolved measurement, high frequency and phase resolution on the 5 Hz–20 kHz range with the present equipment and settings, near-constant spectral sensitivity over a large bandwidth, and no seeding required; measurement possible over the whole combustion volume).

7 December 2011 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
Fabrice GiulianiFabrice Giuliani
Fabrice Giuliani
ALAndreas Lang
Andreas Lang
KGKlaus Johannes Gradl
Klaus Johannes Gradl
PSPeter Siebenhofer
Peter Siebenhofer
JFJohannes Fritzer
Johannes Fritzer
A specific actuator able to modulate the air feed of a gas a burner at a given frequency and amplitude is presented. The Combustion Department at the Institute for Thermal Turbomachinery and Machine Dynamics at the Graz University of Technology has experience on the study of combustion instabilities in gas turbines using a flow excitor. The stability of an industrial burner is tested at elevated pressure and temperature conditions in the frame of the NEWAC project. For practical matters of operation among which the possibility to induce progressively a perturbation when the flame conditions are all set, the need was expressed to design, construct and validate a flexible actuator able to set an air flow modulation at a given frequency and at a desired amplitude level, with the possibility during operation to let these two factors vary in a given range independently from each other. This device should operate within the 0–1 kHz range and 0%–20% amplitude range at steady-state, during transients, or follow a specific time sequence. It should be robust and sustain elevated pressures. The objective is to bring a perturbation in the flow to which the combustor will respond, or not. For elevated levels of pulsation, it can simulate the presence of vortex-driven combustion instabilities. It can also act as a real-time actuator able to respond in frequency and in phase to actively damp a “natural” combustion instability. Other issues are a better and quicker mixing due to the enhanced turbulence level, and pushing forward the blow out limits at lean conditions with controlled injection dynamics. The basic construction is the one of a siren, with an elevated pressure side where the air is throttled, and a low pressure outlet where the resulting sonic jet is sheared by a rotating wheel. A mechanism allows to let vary the surface of interaction between the wheel and the jet. Two electromotors driven by Labview set both frequency and amplitude levels. This contribution describes the actuator’s principles, design, operation range and the results of the characterization campaign.

11 June 2018
Verified
Conference Paper
Closed access
PDF file
Fabrice GiulianiFabrice Giuliani
Fabrice Giuliani
NPNina Paulitsch
Nina Paulitsch
DCDaniele Cozzi
Daniele Cozzi
MGMichael Görtler
Michael Görtler
Lukas AndracherLukas Andracher
Lukas Andracher
In the near future, combustion engineers will shape the burner according to the flame, and not the opposite way anymore. In this contribution, this idea is explored with the help of additive manufacturing (AM). The focus is put on the design and the production of swirlers using advanced materials with the least possible efforts in terms of manufacturing. The material chosen for this study is Inconel 718. There are three motivations to this project. The first one is to design new shapes and assess these in comparison to conventional ones. The second motivation is to be able to manufacture them using additive manufacturing, and to gather know-how on selective laser melting. The third motivation is to elaborate a methodology involving engineering, research and education to promote — only if and when this is desirable — the production of series of premium parts such as high-end components of gas turbine combustor using AM. First-of-a-kind swirler shapes are explained and designed. These are unlikely to be produced using conventional manufacturing. They are then successfully produced in Inconel 718 using AM. The raw parts are directly submitted for testing with no surface post-processing. The paper states why at current state-of-the-art the raw surface quality still needs improvement, and highlights the benefits of the new swirler shape versus conventional.