aparecido carlos gonçalves

Prof. aparecido carlos gonçalves

Mechanical Engineering, UNESP, Ilha Solteira, São Paulo, Brazil
orcid
Full Professor

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2001 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
AGaparecido carlos gonçalves
aparecido carlos gonçalves

22 September 2020 in Journal of Healthcare Engineering
Verified
Journal Article
Open access
AGaparecido carlos gonçalves
aparecido carlos gonçalves
SCSidnei Cavassana
Sidnei Cavassana
FCFábio Roberto Chavarette
Fábio Roberto Chavarette
RORoberto Outa
Roberto Outa
SCSamuel J. Casarin
Samuel J. Casarin
ACAdalberto Vieira Corazza
Adalberto Vieira Corazza
Fear of injection-related pain is a drawback to injectable therapy. Hypodermic injections are a cause for great anxiety and reduced adherence to the subcutaneous application of insulin for glycemic control in diabetics or in the treatment of multiple sclerosis, increasing the risk of complications and mortality. Injured or sick people have to undergo several daily injections, forcing them to rotate the veins and regions used to recover from the trauma caused by the perforation of the skin, tissue, muscles, veins, and arteries. People who suffer from type 1 diabetes mellitus (DM1) need to have their glycemic control 3 to 5 times a day and to take insulin up to 3 times a day. In both cases, the patient needs to perforate the skin. To quantify the pain perceived by the patients depends on the evaluation of each patient and therefore is subjective. This study aims to understand the application and self-application of hypodermic injections and decrease pain during its application and the phobia of the patient, following the reasoning that the lower the effort to penetrate the needle, the less trauma in the tissue and therefore the pain provoked. For that, it was analyzed how some of the characteristics of the needle can influence the sensation of pain in the injection. The needle penetration effort was measured in an artificial tissue (substitute skin model) for different cannula diameters, roughness, depth of penetration, lubrication, and angles of the perforating tip bevel. This study aimed to find alternatives to facilitate the application and self-application of hypodermic injections, increase safety and comfort, and reduce the pain intensity perceived by the patient. To do this, the bevel of needles used repeatedly was analyzed in the profile projector and SEM to verify the loss of the profile or the formation of burrs that could hamper the penetration or traumatize the tissue during the reuse of needles. It has also been mechanically analyzed, which can be done to prevent that the needles used in the subcutaneous application do not inadvertently reach the muscle. The greater penetration effort observed in the needles with greater angle of the bevel is responsible for the patient’s perception of pain.

14 September 2022 in ACS Omega
Verified
Journal Article
Open access
AGaparecido carlos gonçalves
aparecido carlos gonçalves
RFRonaldo Lourenço Ferreira
Ronaldo Lourenço Ferreira
EPEduardo Preto
Eduardo Preto
DKDiogo Karmouche
Diogo Karmouche
FCFábio Roberto Chavarette
Fábio Roberto Chavarette
RORoberto Outa
Roberto Outa
In internal combustion engines, studies of the effects of fuel adulteration focus on problems that occur in the fuel system and pollutants, but little attention is paid to lubricants. Some of these research studies are focused on detecting adulteration rather than the impact of this tampering on the internal combustion engine and lubricant degradation. This work evaluates, in addition to the problems in the supply system, the early degradation of the lubricant from the physical and chemical changes it undergoes when using adulterated gasoline in an internal combustion engine. For that, a 160cc Honda stationary engine mounted on a bench and connected to an alternator through a transmission belt was used. Fuels adulterated with ethanol, kerosene, and thinner were used in proportions of 5, 10, 15, and 20%. The cycles were 40 h each, which is equivalent to approximately 2000 km covered. To measure the engine time and rotation, a tachometer/hourmeter was used, where the time of each cycle was recorded. Particle quantifier analysis (PQA) tests and infrared spectrometry (sulfation, nitriding, oxidation, and total acid number (TBN)) were performed, in addition to changes in engine behavior in relation to rotation. The results showed changes in rotation according to the concentration and type of contaminants. Engine wear was small for the 2000 km covered. The sulfation, nitriding, oxidation, and TBN levels were altered, indicating the degradation of the lubricating oil.

1 March 2011 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
AGaparecido carlos gonçalves
aparecido carlos gonçalves
JSJoão Batista Campos Silva
João Batista Campos Silva

1 April 2006 in Journal of Quality in Maintenance Engineering
Verified
Journal Article
Closed access
PDF file
AGaparecido carlos gonçalves
aparecido carlos gonçalves
RCRodrigo Carvalho Cunha
Rodrigo Carvalho Cunha
DLDaniel Fabiano Lago
Daniel Fabiano Lago
Purpose – The purpose of the paper is to provide information on wear debris on oil and vibration analysis as predictive maintenance techniques in reducer. Design/methodology/approach – The estate of a reducer is verified by analyzing the vibration and oil conditions of a test rig under well-designed conditions utilizing some predictive variables. Findings – According to the vibration and oil analysis it is found out what it was happening into the reducer without disassembling it. Practical implications – This paper demonstrates the use of oil debris analysis and vibration analysis as a technique that enhances preventive maintenance practices. The paper helps practitioners to utilize these techniques more effectively. Originality/value – This paper gives information about two predictive maintenance techniques with a test rig.

15 September 2020 in Shock and Vibration
Verified
Journal Article
Open access
PDF file
APAndre Luis Vinagre Pereira
Andre Luis Vinagre Pereira
AGaparecido carlos gonçalves
aparecido carlos gonçalves
RRRubens Ribeiro
Rubens Ribeiro
FCFábio Roberto Chavarette
Fábio Roberto Chavarette
RORoberto Outa
Roberto Outa
In predictive maintenance, vibration signal analyses are frequently used to diagnose reducer failures because these analyses contain information about the conditions of the mechanical components. Reducer vibration signals are very noisy and the signal-to-noise ratio is so low that extracting information from the signal components is complex, especially in practical situations. Therefore, signal processing techniques are used to solve this problem and facilitate the retrieval of information. In this work, the adopted technique included noise-canceling technique, synchronous temporal mean (TSA), and continuous Morlet wavelet transform (CWT), designed to extract resources and diagnose local gear damage. These techniques are used in measured signals in an experimental workbench consisting of the gear pair coupled to a motor and a generator. The experiment was monitored according to the conditions of a gear pair throughout its useful life. The continuous wavelet transforms accurately identified faults in the gear teeth, and it was possible to detect in which tooth the fault was occurring.