Pollutant emission standards and, in particular, those concerning particles from an internal combustion engine (ICE) are becoming increasingly restrictive. Thus, it is important to determine the main factors related to the production of particulate matter. In this article, the phenomenon of oil sweeping by the blowby gases between the rings/piston/cylinder is investigated. First, a blowby gas simulation model based on experimental results from a Turbocharged Gasoline Direct Injection (TGDI) is developed. From this model, it is possible to characterise the amount of oil swept by the blowby gases. This depends on the endgap position of both the compression and sealing rings. It also depends on the intensity of the blowby flow rate, which is highest at low rpm and high load. At 1500 rpm and full load, this flowrate exceeds 25 mg.cycle−1. From this result, it is possible to quantify the amount of oil swept by these gases as a function of the endgap position. For the quantity of oil swept rises to 20 µg.cycle−1 while for this decreases to 6 µg.cycle−1. The oil concentration of the blowby gas has a direct impact on the particulate emissions because the oil concentration of the backflow gas is inversely proportional to the blowby gas flowrate. As the backflow gases return to the cylinder, the oil oxidises and produces particles. Therefore, it is essential to control the oil concentration of the backflow gases. In addition, the simulation model shows the blowby flowrate becomes negative and decreases to −3.4 mg. cycle−1 in idle conditions. The amount of oil swept by the blowby is no longer directed towards the oil pan, but towards the piston crown. This phenomenon of oil storage of the piston crown in idle condition is proportional to the duration of the idle time. In order to confirm these results, experimental tests are carried out on a TGDI engine. It appears that when the idling time changes from 0 s to 7 s between two strictly identical accelerations, the level of particulate emissions is multiplied by 1.3. When the idling time changes from 0 s to 22 s between two strictly identical accelerations, the level of particulate emissions is multiplied by 3. These results confirm the mechanism of oil storage at idle highlighted by the simulation model.
Particulate emission from internal combustion engines is a complex phenomenon that needs to be understood in order to identify its main factors. To this end, it appears necessary to study the impact of unburned gases, called blow-by gases, which are reinjected into the engine intake system. A series of transient tests demonstrate their significant contribution since the particle emissions of spark-ignition engines are 1.5 times higher than those of an engine without blow-by with a standard deviation 1.5 times greater. After analysis, it is found that the decanter is not effective enough to remove completely the oil from the gases. Tests without blow-by gases also have the advantage of having a lower disparity, and therefore of being more repeatable. It appears that the position of the “endgap” formed by the first two rings has a significant impact on the amount of oil transported towards the combustion chamber by the backflow, and consequently on the variation of particle emissions. For this engine and for this transient, 57% of the particulate emissions are related to the equivalence ratio, while 31% are directly related to the ability of the decanter to remove the oil of the blowby gases and 12% of the emissions come from the backflow. The novelty of this work is to relate the particles fluctuation to the position of the endgap ring.
Les émissions de particules d’un moteur à combustion interne de type allumage commandé sont très variables. La richesse du mélange air/carburant ne suffit pas à définir parfaitement la fonction de caractérisation de ces émissions. Des essais ont souligné l’importance du phénomène de balayage de l’huile par les gaz du blowby sur les émissions de particules Ceci est due à la position des segments qui tournent continuellement autour de leurs gorges. La fonction de caractérisation des émissions de particules a été complété en tenant compte de ces nouvelles conditions. Puis, la création d’un modèle de simulation des gaz du blowby sous GT-suite a permis de caractériser ces flux et d’appréhender ces mécanismes. Par exemple, au ralenti, il se créé un phénomène d’accumulation d’huile sur la couronne du piston. Des essais expérimentaux ont confirmé l’importance de la durée du ralenti sur les émissions de particules. Enfin, l’étude de l’impact du vieillissement de l’huile et du filtre à huile sur les émissions de particules a été investiguée. Un ensemble « huile + filtre » vieillit dans des conditions réelles présente un taux d’émission de particules deux fois plus important qu’un ensemble neuf. Finalement ces travaux ont permis de compléterla fonction de caractérisation des émissions de particules afin d’être plus en adéquation avec les conditions réelles de fonctionnement d’un moteur à combustion interne de type allumage commandé.