Appropriate vehicle lateral stability control is the key to ensure vehicle driving safety, whereas accurate lateral stability recognition can help improve the performance of vehicle control. In this article, the vehicle stability recognition and coordinated control are studied. Firstly, the vehicle dynamic model is established, through vehicle simulation software Carsim, the attribute dataset representing the vehicle lateral stability is further obtained. Then, clustering by fast search and find of density peaks method (CFSFDP) based procedure for the classification of the lateral stability as ‘Absolutely stability’, ‘Nearly stability’ and ‘Hardly stability’ is applied. The brain emotional learning network combined with genetic algorithm (GA-BEL) model is used to train datasets to recognize vehicle stability categories during driving. For the different recognition results, a coordinated control strategy based on active front steering control (AFS) and direct yaw moment control (DYC) is designed finally. Through the Carsim/Simulink co-simulations and Hardware-in-the-Loop tests under several typical driving conditions, the superiorities of the stability recognition method and the coordinated control strategy proposed in this paper are verified.
10 January 2024 in IEEE Transactions on Vehicular Technology
In the man-machine co-driving, most of the existing indirect cooperative shared steering control(ICSSC) strategies adopt fixed driver models and are designed based on rules. However, the fixed driver model is difficult to match with the actual situation, and the rule-based strategy is hard to be designed under the multi-dimensional feature input and the multi-objective conditions and require complicated parameters adjustment. A driver model that conforms to the driving characteristics of drivers with actual driving data is established, and an ICSSC strategy is proposed based on reinforcement learning in this paper, so as to realize the dynamic allocation of human-machine steering driving weight. Firstly, the vehicle dynamics model is established according to the vehicle longitudinal, lateral and yaw dynamics, the driver driving data is collected, and then the trajectory tracking MPC (Model Predictive Control) steering controller is designed. Secondly, DQN (Deep Q-Network), DDPG (Deep Deterministic Policy Gradient) and TD3 (Twin Delayed Deep Deterministic Policy Gradient) reinforcement learning schemes that can adapt to the complex state variables are selected to design ICSSC strategies, where TD3 obtains the best iterative convergence effect under the same reward function and input state conditions. Compared with the rule-based strategy, the tracking accuracy, driving comfort, man-machine conflict, driver and controller load indexes are designed to evaluate the ICSSC strategy. Finally, simulation and hardware in the loop experiment results show that the ICSSC strategy based on TD3 can dynamically allocate the steering weights of the driver and controller under multi-objective conditions more effectively.
19 July 2021 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
The performance of the model-based controller is always affected by the uncertainty and nonlinearity of the model parameters in the vehicle path tracking process. To address this issue, a novel path tracking controller based on model-free adaptive dynamic programming (ADP) is proposed for autonomous vehicles in this paper. To be specific, the proposed controller obtains information from the online state and front-wheel angle input data which are repeatedly used to calculate the controller gain iteratively. So, this controller features not requiring accurate knowledge of vehicle model parameters for controller development. Meanwhile, the path tracking performance of the autonomous vehicle will be inevitably disturbed by unknown nonlinear external disturbance. To approximate this disturbance, the learning characteristics of Radial Basis Function Neural Network (RBFNN) are applied to generate compensation for the front-wheel angle. Afterward, the weight updating law of RBFNN is derived by Lyapunov function to ensure the stability and convergence of the whole system. Finally, Hardware in the loop (HIL) test results demonstrate that the proposed ADP-RBF controller can improve the comprehensive performance of the vehicle path tracking control system and achieve the balance between path tracking accuracy and minimum sideslip angle.
2 August 2022 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Distributed drive vehicles are prone to wheel slip during driving on low adhesion coefficient roads. Wheel slip will not only cause energy loss, but also the different driving states of the two sides of the wheels will lead to a sharp deterioration in vehicle stability, which will adversely affect the dynamics and safety of the vehicle. For the control characteristics of distributed drive vehicles, a slip rate controller is designed on the basis of slip rate estimation, and a stability control strategy adapted to straight and steering driving are proposed. Firstly, the road surface is identified based on the Burckhardt tire model, and the optimal slip rate of the current road surface is estimated. And the optimal wheel speed corresponding to the current vehicle speed is calculated. An active disturbance rejection controller (ADRC) is established, which controls the four-wheel speeds by adjusting the motor output torque and tracks the optimal wheel speed corresponding to the optimal slip rate. The sliding-mode controller is designed considering the stability requirements of the vehicle during high-speed steering. And the wheel output torque is optimally allocated based on the quadratic programing method. Finally, joint simulations and hardware-in-the-loop tests verify the effectiveness of the control strategy proposed in this paper.
An adaptive cruise control (ACC) system can reduce driver workload and improve safety by taking over the longitudinal control of vehicles. Nowadays, with the development of range sensors and V2X technology, the ACC system has been applied to curved conditions. Therefore, in the curving car-following process, it is necessary to simultaneously consider the car-following performance, longitudinal ride comfort, fuel economy and lateral stability of ACC vehicle. The direct yaw moment control (DYC) system can effectively improve the vehicle lateral stability by applying different longitudinal forces to different wheels. However, the various control objectives above will conflict with each other in some cases. To improve the overall performance of ACC vehicle and realize the coordination between these control objectives, the extension control is introduced to design the real-time weight matrix under a multi-objective model predictive control (MPC) framework. The driver-in-the-loop (DIL) tests on a driving simulator are conducted and the results show that the proposed method can effectively improve the overall performance of vehicle control system and realize the coordination of various control objectives.
16 May 2019 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
In the traditional lane keeping system, a single control algorithm is used for global-region control, which often results in poor control effect in some control areas. In view of this problem, a control method combining the extension control and Takagi-Sugeno-Kang fuzzy control is proposed for lane keeping system control. The extension control strategy based on the idea of control with area division divides different control regions according to the states of the system, and adopts different control algorithms in different control areas to address the limitation of a single control algorithm. For the randomness and inaccuracy of artificial experience in control domain division, a method for control domain division based on the density distribution of characteristic plane is proposed in this article. In order to further improve and explore the performance of extension control, Takagi-Sugeno-Kang extension controller is designed with Takagi-Sugeno-Kang fuzzy control theory, and the extension control performance is improved when switching among different control algorithms. The proposed control strategy is simulated and tested on the CarSim/Simulink joint simulation platform and the CarSim/LabVIEW hardware-in-loop test bench, respectively. The results show that the proposed control strategy can effectively keep the vehicle near the center line of the lane, and both the lane keeping control accuracy and vehicle stability are improved, which guarantees driving safety and comfort.