Tran Anh Dung

Dr. Tran Anh Dung

University of Transport and Communications, Hanoi, Hà Nội, Vietnam
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in Journal of the Mechanical Behavior of Materials
Verified
Journal Article
Open access
PDF file
Tran Anh DungTran Anh Dung
Tran Anh Dung
MTMai Van Tham
Mai Van Tham
DQDo Xuan Quy
Do Xuan Quy
TTTran The Truyen
Tran The Truyen
PKPham Van Ky
Pham Van Ky
LHLe Hai Ha
Le Hai Ha
This paper presents simulation calculations and experimental measurements to determine the dynamic load factor (DLF) of train on the urban railway in Vietnam. Simulation calculations are performed by SIMPACK software. Dynamic measurement experiments were conducted on Cat Linh – Ha Dong line. The simulation and experimental results provide the DLF values with the largest difference of 2.46% when the train speed varies from 0 km/h to 80 km/h

28 October 2020
Verified
Book Chapter
Closed access
PDF file
Tran Anh DungTran Anh Dung
Tran Anh Dung
TTTran The Truyen
Tran The Truyen
NPNguyen Hong Phong
Nguyen Hong Phong
PKPham Van Ky
Pham Van Ky
LHLe Hai Ha
Le Hai Ha

28 October 2021
Verified
Book Chapter
Closed access
PDF file
Tran Anh DungTran Anh Dung
Tran Anh Dung
MTMai Van Tham
Mai Van Tham
TTTran The Truyen
Tran The Truyen

5 December 2023 in The Open Construction & Building Technology Journal
Verified
Journal Article
Open access
PDF file
Tran Anh DungTran Anh Dung
Tran Anh Dung
DQDo Xuan Quy
Do Xuan Quy
Aims: This study aims to determine the in-plane stiffness of the track in a turnout of the railway in Vietnam. Background: Track stiffness is a basic parameter of railway tracks that influences the bearing capacity of the track, the dynamic behavior of passing vehicles, the quality of track geometry, and the life of track components. Objective: The objective of this research is to determine the in-plane stiffness of the track based on substructure modulus, and rail pad stiffness at a track section in a turnout. Methods: Various tests which included the field tests of the substructure modulus, and rail pad stiffness tests in the laboratory were done. Substructure modulus was investigated at ten locations in the field. Rail pad stiffness was tested with five samples in the laboratory. In-plane stiffness of the track was calculated through substructure modulus and rail pad stiffness. The finite element method was used to evaluate the bearing capacity of bearings with different in-plane stiffness values. Results: Based on the results obtained, the substructure modulus was from 0.49 N/mm3 to 1.48 N/mm3. The rail pad stiffness is from 32.99 kN/mm to 34.92 kN/mm. These results are used to calculate the in-plane stiffness of the track. The in-plane stiffness of a track section in a turnout in Vietnam is from 25.18 kN/mm to 30.19 kN/mm. According to the finite element method, it is possible to determine the maximum value of forces transmission to the supports from 37.743 kN to 38.989 kN corresponding to the above stiffness values with the axle load of train 14 tons and rail P60. Conclusion: The stiffness of the supporting is proportional to the value of the force transmitted to the supporting. This study clearly showed that the substructure (soil and ballast) properties had the most impact on the total in-plane stiffness of the track. The results will be a tool for the track maintenance engineer to implement correct maintenance activities.

8 November 2022 in Infrastructures
Verified
Journal Article
Open access
PDF file
Tran Anh DungTran Anh Dung
Tran Anh Dung
Said EasaSaid Easa
Said Easa
Previous studies have addressed railway turnouts (switches and crossings), but research on the performance of 1000 mm gauge turnouts is limited. At present, wooden sleeper structures are used at turnouts in Vietnam. However, these structures have many disadvantages in the operation process. This paper evaluates the performance of new prestressed bearer (PSB) for turnouts, designed for the 1000 mm gauge, to overcome the disadvantages of a wooden sleeper. Test samples of PSB were manufactured in the factory, and experiments were conducted in the laboratory according to European Standards to evaluate the PSB carrying capacity. The test results show that the proposed structure meets the carrying capacity under the standard test loads. In addition, the results of the static and fatigue tests of the bearers show a considerable reserve in the cross-section capacity. This means that the existing reserve can be used with a larger locomotive axle, and the bearer design can be optimized by arranging the prestressed strands and changing the bearer cross-section’s geometric dimensions. It is hoped that the proposed bearer design will be a viable alternative for designing railway turnouts.

11 October 2019
Verified
Book Chapter
Closed access
PDF file
PHPham Van Hung
Pham Van Hung
TTTran The Truyen
Tran The Truyen
Tran Anh DungTran Anh Dung
Tran Anh Dung
DQDoan Bao Quoc
Doan Bao Quoc
LHLe Hai Ha
Le Hai Ha
NPNguyen Hong Phong
Nguyen Hong Phong