Thermoelectric materials generate electric energy from waste heat, with conversion efficiency governed by the dimensionless figure of merit, ZT. Single-crystal tin selenide (SnSe) was discovered to exhibit a high ZT of roughly 2.2–2.6 at 913 K, but more practical and deployable polycrystal versions of the same compound suffer from much poorer overall ZT, thereby thwarting prospects for cost-effective lead-free thermoelectrics. The poor polycrystal bulk performance is attributed to traces of tin oxides covering the surface of SnSe powders, which increases thermal conductivity, reduces electrical conductivity and thereby reduces ZT. Here, we report that hole-doped SnSe polycrystalline samples with reagents carefully purified and tin oxides removed exhibit an ZT of roughly 3.1 at 783 K. Its lattice thermal conductivity is ultralow at roughly 0.07 W m^–1 K^–1 at 783 K, lower than the single crystals. The path to ultrahigh thermoelectric performance in polycrystalline samples is the proper removal of the deleterious thermally conductive oxides from the surface of SnSe grains. These results could open an era of high-performance practical thermoelectrics from this high-performance material.

Thermoelectric materials have attracted significant research interest in recent decades due to their promising application potential in interconverting heat and electricity. Unfortunately, the strong coupling between the material parameters that determine thermoelectric efficiency, i.e., the Seebeck coefficient, electrical conductivity, and thermal conductivity, complicates the optimization of thermoelectric energy converters. Main‐group chalcogenides provide a rich playground to alleviate the interdependence of these parameters. Interestingly, only a subgroup of octahedrally coordinated chalcogenides possesses good thermoelectric properties. This subgroup is also characterized by other outstanding characteristics suggestive of an exceptional bonding mechanism, which has been coined metavalent bonding. This conclusion is further supported by a map that separates different bonding mechanisms. In this map, all octahedrally coordinated chalcogenides with good performance as thermoelectrics are located in a well‐defined region, implying that the map can be utilized to identify novel thermoelectrics. To unravel the correlation between chemical bonding mechanism and good thermoelectric properties, the consequences of this unusual bonding mechanism on the band structure are analyzed. It is shown that features such as band degeneracy and band anisotropy are typical for this bonding mechanism, as is the low lattice thermal conductivity. This fundamental understanding, in turn, guides the rational materials design for improved thermoelectric performance by tailoring the chemical bonding mechanism.

Thermoelectric interface materials (TEiMs) are essential to the development of thermoelectric generators. Common TEiMs use pure metals or binary alloys but have performance stability issues. Conventional selection of TEiMs generally relies on trial-and-error experimentation. We developed a TEiM screening strategy that is based on phase diagram predictions by density functional theory calculations. By combining the phase diagram with electrical resistivity and melting points of potential reaction products, we discovered that the semimetal MgCuSb is a reliable TEiM for high-performance MgAgSb. The MgCuSb/MgAgSb junction exhibits low interfacial contact resistivity (ρ _c <1 microhm square centimeter) even after annealing at 553 kelvin for 16 days. The fabricated two-pair MgAgSb/Mg _3.2 Bi _1.5 Sb _0.5 module demonstrated a high conversion efficiency of 9.25% under a 300 kelvin temperature gradient. We performed an international round-robin testing of module performance to confirm the measurement reliability. The strategy can be applied to other thermoelectric materials, filling a vital gap in the development of thermoelectric modules.

Laser‐assisted field evaporation is studied in a large number of compounds, including amorphous and crystalline phase change materials employing atom probe tomography. This study reveals significant differences in field evaporation between amorphous and crystalline phase change materials. High probabilities for multiple events with more than a single ion detected per laser pulse are only found for crystalline phase change materials. The specifics of this unusual field evaporation are unlike any other mechanism shown previously to lead to high probabilities of multiple events. On the contrary, amorphous phase change materials as well as other covalently bonded compounds and metals possess much lower probabilities for multiple events. Hence, laser‐assisted field evaporation in amorphous and crystalline phase change materials reveals striking differences in bond rupture. This is indicative for pronounced differences in bonding. These findings imply that the bonding mechanism in crystalline phase change materials differs substantially from conventional bonding mechanisms such as metallic, ionic, and covalent bonding. Instead, the data reported here confirm a recently developed conjecture, namely that metavalent bonding is a novel bonding mechanism besides those mentioned previously.