Agah Oktay ERTAY

Dr. Agah Oktay ERTAY

Electrical and Electronics Engineering, Erzincan Binali Yildirim University, Erzincan, Turkey (Türkiye)
orcid
Electromagnetics, Microwave Engineering

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2017 in IET Microwaves, Antennas & Propagation
Verified
Journal Article
Open access
PDF file
MAMehmet Abbak
Mehmet Abbak
MAMehmet Nuri Akinci
Mehmet Nuri Akinci
Agah Oktay ERTAYAgah Oktay ERTAY
Agah Oktay ERTAY
SÖSelçuk Özgür
Selçuk Özgür
CICevdet Işık
Cevdet Işık
IAİbRahim Akduman
İbRahim Akduman
In this study, the authors present a novel dipole antenna for microwave imaging (MWI) applications. Different from the previous works, the designed dipole is compact while having a wide‐impedance bandwidth of 1–4.2 GHz along with a moderate gain. In particular, the largest dimension of the antenna is 6 cm, which is 0.2 wavelength at the very lower end of the operating frequency bandwidth. Furthermore, the resultant design has a cross‐polarisation level <20 dB. Important characteristics of the proposed design are given with the simulations through analysis system high‐frequency structure simulator. Obtained simulation results are also shown to be consistent with the measurements. In addition to measuring fundamental parameters of the designed dipole, they also test the proposed antenna in a circular MWI system. In this context, several dielectric scatterers are measured in a circular scanner and obtained scattered field measurements are supplied to the well‐known contrast source inversion method. Imaging results show that the proposed antenna is quite suitable for MWI applications.

14 July 2015 in International Journal of Microwave and Wireless Technologies
Verified
Journal Article
Closed access
PDF file
Agah Oktay ERTAYAgah Oktay ERTAY
Agah Oktay ERTAY
MAMehmet Abbak
Mehmet Abbak
SŞSerkan Şimşek
Serkan Şimşek
In this paper a novel low pass filter (LPF) design procedure is proposed for electromagnetic bandgap based microstrip filters without using classical filter design approach. LPF is designed for ultra-wide stopband and sharp roll-off rate via proposed design procedure. It has been shown that finite periodic fan-shaped defected ground structures (FSDGSs) and double radial stubs (DRSs) yield broad stopband and very sharp transition band. The proposed LPF has −3 dB passband from dc to 1.49 GHz, and −20 dB broad stopband from 1.65 GHz up to 7.41 GHz. Full wave electromagnetic (EM) simulation of the proposed filter is achieved with ANSYS's High Frequency Structure Simulator (HFSS) and equivalent circuit (EC) model of the filter is proposed and verified via Applied Wave Research (AWR) software. To verify the simulations, filter is realized on ARLON AD1000 substrate, and measured with Agilent 5245A PNA-X Vector Network Analyzer. Measurement results of fabricated filter are in good agreement with EM and EC simulations.

26 April 2023 in IEEE Access
Verified
Journal Article
Open access
DGDurmus Gebesoglu
Durmus Gebesoglu
Agah Oktay ERTAYAgah Oktay ERTAY
Agah Oktay ERTAY
SSSerkan Simsek
Serkan Simsek
Electromagnetic Bandgap (EBG) structures that exhibit various performances, such as preventing the electromagnetic wave propagation and reflecting an incident wave within the stopband, have unique electromagnetic characterization. Due to this reason, accurate analysis and design of the EBG structures are crucial to enhance the integrated system performance. This paper concentrates on the characterization of some planar EBGs using the Auxiliary Functions of Generalized Scattering Matrix (AFGSM) methods, with particular importance on an in-depth consideration of its bandgaps. The AFGSM method is applied to the planar EBG structures in the literature for the first time. The well-known kinds (symmetric and asymmetric cases) of mushroom type and multilayer EBG structures are considered to verify the presented method. Analysis results are compared with the Conventional Eigenvalue Equation (C-EIV) and the Generalized Scattering Matrix based Eigenvalue Equation (GSM-EIV) methods. Low computation load and accurate results are obtained to analyze the planar EBG structures with the AFGSM method due to using transmission line model. In addition, a design methodology is proposed for a chosen planar EBG structure using the AFGSM methods. Geometrical parameters of interested EBG problems are determined for acquiring the stopband frequency region of interest using the scattering parameters of unit cell configuration. The mushroom EBG model along one and two-dimensional axes is used in an antenna application to decrease mutual coupling between antenna elements. Three different scenarios are simulated in the HFSS electromagnetic simulation design environment to understand the effect of mutual coupling reduction in the antenna problem of the designed EBG structure via the AFGSM method. All designed antennas are manufactured, and the measurement results are in good agreement with the simulation results. The measurement results of the fabricated antenna application example including designed EBG using the proposed AFGSM method is compared with the existing similar problems with the same and different EBG models. It has been demonstrated that bandgap analysis, design of the planar EBG structures and integration of considered EBG model to a design application can be accurately and quickly achieved with the given methodology using the AFGSM method.

2 January 2017
Verified
Conference Paper
Closed access
Agah Oktay ERTAYAgah Oktay ERTAY
Agah Oktay ERTAY
SSSerkan Simsek
Serkan Simsek
The main objective of this work is to present a compact microstrip bandstop filter for X-band applications. The designed filter covers X-band and has stopband bandwidth with better than 2.5GHz for -20dB. Maximum |S11| value in the passband region is below -15dB for the final filter. Optimum distributed bandstop filter design method is used to acquire the design goals. The final filter has a compact size with 12.87mm × 7.04mm. Two-stage design procedure is proposed to realize design objectives. It is proposed in the first stage of the design procedure to have realizable open stubs which is difficult to implement for given dielectric substrate properties. To remedy this difficulty, a wide stopband region is selected. The second stage of the design procedure presents an optimization process to achieve desired filter. In order to examine the frequency responses of all design steps, three commercial electromagnetic simulators are used. Consistent simulation results are obtained before implementation.

27 August 2018 in AEU - International Journal of Electronics and Communications
Verified
Journal Article
Closed access
Agah Oktay ERTAYAgah Oktay ERTAY
Agah Oktay ERTAY
SŞSerkan Şimşek
Serkan Şimşek

7 September 2021 in International Journal of Circuit Theory and Applications
Verified
Journal Article
Closed access
PDF file
Agah Oktay ERTAYAgah Oktay ERTAY
Agah Oktay ERTAY
SSSerkan Simsek
Serkan Simsek