1 August 2022 in Progress in Orthodontics
Background: Clear aligner treatment has become popular over recent years. It is necessary to identify methods by which we could avoid the bowing effect in extractions with clear aligner. The present study was to identify the appropriate method to design torque movement involving the upper anterior teeth of extraction cases, in order to maintain or improve the axis and torque of the upper anterior teeth with a clear aligner during movement and closure of the extraction space. Results: As the height of the power ridge increased, the rotation angle of the upper central incisor in the sagittal direction decreased gradually and the location of the rotation center changed significantly; the rotation center moved in the apical direction and then changed to the crown side. The highest von-Mises stress of the upper central incisor root, periodontal ligaments, and alveolar bone, showed little change as the power ridge height increased. When the axial inclination of the upper central incisor was normal (U1-SN = 105°), the tendency of movement for the upper central incisor approached translation with a power ridge height of 0.7 mm (corresponding distorted angle: 5.8415). When the axial inclination of the upper central incisor was oversized (U1-SN = 110°), the axial inclination of the upper central incisor reduced to normal following completion of the anterior segment retraction with a power ridge of 0.4 mm (corresponding distorted angle: 3.4265). Conclusion: Analysis indicates that pure palatal tipping movement of the upper anterior teeth is generated without torque control, thus resulting in the bowing effect. The required torque control of the upper anterior teeth with oversize axial inclination is weaker than that of the upper anterior teeth with normal axial inclination because limited torque loss is expected for oversize axial inclination teeth. Variation sensitivity of the rotation center should be considered carefully due to biological problems when designing translation of the upper anterior teeth with normal axial inclination.
5 May 2025 in Progress in Orthodontics
Objective: Molar sequential distalization with clear aligners was advantageous. However, the effect of periodontal status on it has yet to be investigated. This study aimed to analyze the influence of the different periodontal states on molar distalization to reduce the adverse mechanical stimulation caused by periodontal states by the different stagings of movement and further explore therapeutic recommendations for clinical practice. Methods: To ascertain the initial displacement of dentition and periodontal ligament (PDL) hydrostatic stress, finite element models (FEMs) were developed. These models included the distalization of the second molars (Step A) and the first molar (Step B) in three distinct periodontal conditions (simulating the periodontal state of mild, moderate, and severe periodontitis) and three distinct distances (0.10 mm, 0.18 mm, 0.25 mm). Results: Periodontal status affected the tooth movement during molar distalization. During the molar distalization with 0.25 mm step distance, the initial displacement of the molar was greater in the model with worse periodontal condition. However, it did not increase the efficiency of tooth movement because the initial displacement is accompanied by tipping. Moreover, the second molar relapse to mesialization for a reaction from the first molar distalization affected efficiency. Fortunately, reducing the step distance could control those undesired tooth movements positively associated with alveolar bone resorption. Limitations: The finite element method cannot simulate complex periodontal conditions in clinical practice. Conclusion: To reduce the undesired tipping and relapse, the personalized staging of movement should be designed according to the periodontal condition. Designing 0.18 mm step distance for patients with 1/3 alveolar bone resorption is recommended, whereas patients with 1/2 alveolar bone resorption need 0.1 mm. These recommendations can guide orthodontists in designing effective treatment plans for patients with varying degrees of periodontal disease.
18 February 2025 in Clinical Oral Investigations
Background To measure the actual moving direction and displacement of the root and crown of maxillary teeth before and after treatment in molar distalization cases using clear aligners(CAs). Materials and methods This retrospective study included 28 adult patients who received maxillary distalization treatment with CAs. The pre- and post-treatment CBCT were superimposed and the crown and root of all maxillary teeth were marked. Achieved and predicted three-dimensional displacement of maxillary teeth were then compared using the paired t test. Mixed-effect model was used to explore the influence of different staging design (one-molar distalization vs. two-molar distalization) and anchorage (TAD vs. Class II elastic vs. no extra anchorage management). Results Labial displacement happened to the anterior teeth even the palatal displacement was prescribed. Body distalization of maxillary posterior teeth could not be fully achieved as predicted. The premolars and molars achieved greater distal tipping, buccal inclination, and less distal displacement than predicted. In buccal-palatal dimension, the greatest buccal tipping tendency happened to the 2nd premolar and decreased toward the distal portion of the aligner. In the mesial-distal dimension, the highest accuracy of molar distalization was found in the 2nd molars while the lowest in the 1st premolars. No significant difference was found between two molar distalization patterns. Extra anchorage management devices could not diminish the difference between the predicted and achieved displacement. Conclusions The achieved molar distalization displacement and anterior teeth retraction is not as good as expected using CAs. The anterior and posterior anchorage loss cannot be completely avoided despite extra anchorage management devices are adopted. The potential reason for the correction of class II malocclusion needs further exploration.
30 December 2023 in International Orthodontics
This case report describes a 19-year-old man presented with a 5.7-mm deep overbite, Class II division 2 malocclusion with the right upper maxillary canine completely buccal ectopia, deviated midline in the upper arch, severe crowding and retroclination of the maxillary and mandibular incisors. The patient was treated with clear aligners to correct the Class II relationship and the deep overbite. A series of clear aligners were used to move bilateral maxillary molars distally with unilateral mini-screw anchorage. The final results showed that clear aligners with mini-screws could effectively achieve the required upper distal molar movement thanks to a reasonable design of the stages and anchorage. The treatment was completed in 19 months and the patient was satisfied with the treatment outcome in this context of mild to moderate Class II division 2 malocclusion.
28 November 2025 in International Dental Journal
To investigate movements of maxillary teeth in four-premolar extraction cases treated with clear aligners (CAs), as well as their influencing factors. Forty-seven patients underwent four first or second premolars extractions having been treated with CAs. CBCT images were collected pre- and post-treatment for superimposition and measurement. A paired t-test was employed to compare designed and achieved tooth movements. A linear mixed-effects model was utilized to study the effects of designed tooth movements, age, different premolar extractions, anchorage methods, space closing patterns and attachment types on the tooth movements. In the anteroposterior direction, the movements of the incisor crowns were fully achieved, whereas the roots were only poorly achieved. Both the roots and crowns of the canines showed less distal displacement than expected, especially the roots. The crowns of the posterior teeth exhibited greater forward movement than expected compared with their roots. In the lateral displacement (LD), the incisors failed to move distally, with the U2 root showing the greatest discrepancy (P < .001). In the occlusal-gingival direction, the incisor crowns demonstrated increased extrusion, particularly U1. Adolescents exhibited greater discrepancies in U1 crown movements compared with adults (P < .001). Although the magnitude of U6 root discrepancies in LD was similar between adolescents and adults, the direction of movement differed significantly (P < .001). The factors that significantly influenced treatment outcomes included age, staging strategy, attachment design, and anchorage methods. In premolar-extraction with CAs, the root of the incisors and entire canines required more retraction in design, and the crown needed more intrusion. Miniscrews can cause uncontrolled tilting movement of U1. Different space closing patterns and attachment types affected the anterior teeth and the anchorage of posterior teeth. These findings provide references for optimizing a treatment plan design using clear aligner treatment.