21 December 2011 in PLOS ONE
Estimation of an individual muscle force still remains one of the main challenges in biomechanics. In this way, the present study aimed: (1) to determine whether an elastography technique called Supersonic Shear Imaging (SSI) could be used to estimate muscle force, (2) to compare this estimation to that one provided by surface electromyography (EMG), and (3) to determine the effect of the pennation of muscle fibers on the accuracy of the estimation. Eleven subjects participated in two experimental sessions; one was devoted to the shear elastic modulus measurements and the other was devoted to the EMG recordings. Each session consisted in: (1) two smooth linear torque ramps from 0 to 60% and from 0 to 30% of maximal voluntary contraction, for the first dorsal interosseous and the abductor digiti minimi, respectively (referred to as “ramp contraction”); (2) two contractions done with the instruction to freely change the torque (referred to as “random changes contraction”). Multi-channel surface EMG recordings were obtained from a linear array of eight electrodes and the shear elastic modulus was measured using SSI. For ramp contractions, significant linear relationships were reported between EMG activity level and torque (R2 = 0.949±0.036), and between shear elastic modulus and torque (R2 = 0.982±0.013). SSI provided significant lower RMSdeviation between measured torque and estimated torque than EMG activity level for both types of contraction (1.4±0.7 vs. 2.8±1.4% of maximal voluntary contraction for “ramp contractions”, p<0.01; 4.5±2.3 vs. 7.9±5.9% of MVC for “random changes contractions”, p<0.05). No significant difference was reported between muscles. The shear elastic modulus measured using SSI can provide a more accurate estimation of individual muscle force than surface EMG. In addition, pennation of muscle fibers does not influence the accuracy of the estimation.
1 September 2010 in Journal of Applied Physiology
The aim of this study was to determine the effects of 14 wk of plyometric training on mechanical properties of the Achilles tendon. Nineteen subjects were randomly assigned to trained or control group. Cross-sectional area (CSA), stiffness, and dissipation coefficient of the Achilles tendon were measured before and after the training period. In the trained group, a decrease in dissipation coefficient (−35.0%; P < 0.05) and an upward trend in stiffness (+24.1%) of the Achilles tendon was found, without any changes in Achilles tendon CSA (P > 0.05). Plyometric training enhances the muscular tension transmission mainly through a reduction in energy dissipated by the tendon. The lack of changes in the Achilles tendon CSA indicates that changes in mechanical properties would mainly result from a qualitative change in tendinous tissues rather than from changes in the geometry of the Achilles tendon.
1 September 2013 in Journal of Biomechanics
2 March 2017 in Journal of Anatomy
1 July 2008 in Journal of Biomechanics
29 September 2015 in PLOS ONE
The mechanical properties of hamstring muscles are usually inferred from global passive torque/angle relationships, in combination with adjoining tissues crossing the joint investigated. Shear modulus measurement provides an estimate of changes in muscle-tendon stiffness and passive tension. This study aimed to assess the passive individual behavior of each hamstring muscle in different stretching positions using shear wave elastography. The muscle shear modulus of each hamstring muscle was measured during a standardized slow passive knee extension (PKE, 80% of maximal range of motion) on eighteen healthy male volunteers. Firstly, we assessed the reliability of the measurements. Results were good for semitendinosus (ST, CV: 8.9%-13.4%), semimembranosus (SM, CV: 10.3%-11.2%) and biceps femoris long-head (BF-lh, CV: 8.6%-13.3%), but not for biceps femoris short-head (BF-sh, CV: 20.3%-44.9%). Secondly, we investigated each reliable muscle in three stretch positions: 70°, 90° and 110° of hip flexion. The results showed different values of shear modulus for the same amount of perceived stretch, with the highest measurements in the high-flexed hip situation. Moreover, individual muscles displayed different values, with values increasing or BF-lh, SM and ST, respectively. The inter-subject variability was 35.3% for ST, 27.4% for SM and 30.2% for BF-lh. This study showed that the hip needs to be high-flexed to efficiently tension the hamstrings, and reports a higher muscle-tendon stress tolerance at 110° of hip angle. In addition muscles have different passive behaviors, and future works will clarify if it can be linked with rate of injury.