Purpose: To compare microleakage of calcium silicate-based cement (Biodentine, BD) used alone or covered with glass ionomer cement (GIC) or resin composite (RC) and matured for 12 min (12mBD) or 24 h (24hBD).Methods: Seventy-two extracted premolars with class I cavities were divided into two groups (n = 36) based on BD maturation time (12 min and 24 h). Each group was then subdivided by restoration type into three subgroups (n = 12 each): BD only, BD + GIC, and BD + RC. After pH cycling, thermocycling, and methylene blue immersion, microleakage was assessed with a stereomicroscope. Data were analyzed using two-way ANOVA and the chi-square test (P < 0.05).Results: Microleakage scoring showed that 12mBD + RC had the least dye penetration, significantly less than 24hBD and 24hBD + GIC. The 12mBD + RC group also had the lowest microleakage proportion. For both BD and BD + GIC, microleakage proportions were significantly lower after 12 min of maturation than after 24 h of maturation.Conclusion: BD matured for 12 min exhibited microleakage equal to or less than that of the 24-h groups. Additionally, sealing was better for restorations with RC over BD than for those with BD alone or BD combined with GIC.
27 April 2026 in Biomaterial Investigations in Dentistry
Objectives: This study aimed (1) to compare the shear bond strength (SBS) and failure modes of Biodentine™ (BD) specimens bonded with resin composite (RC) or high-viscosity glass ionomer cement (HVGIC) at different maturation times and (2) to compare the SBS of BD bonded with RC using different adhesive systems. Materials and Methods: Part I: A total of 120 BD specimens were bonded with either RC or HVGIC (n = 60 each), then divided into four groups (n = 15 each) based on BD maturation time: 12 min, 24 h, 48 h, and 1 week. Part 2: A total of 45 BD specimens matured for 24 h were bonded with RC using 3 adhesives (n = 15 each): (1) Single Bond Universal (SU) with self-etched technique (SU-SE), (2) Adper Single Bond 2 adhesive with etch and rinse technique (AS-ER), and (3) SU adhesive with etch-and-rinse technique (SU-ER). All specimens underwent pH cycling and thermocycling. SBS was measured using a universal testing machine, and failure modes were examined under a stereomicroscope. Results: BD bonded with RC showed significantly higher SBS than BD bonded with HVGIC at all BD maturation times (p < 0.05). No significant SBS differences were found within RC groups, except between the 24-h and 1-week. Cohesive failure predominated in RC specimens (70%), whereas adhesive failure prevailed in HVGIC specimens (71.7%). SU-ER had significantly higher SBS than SU-SE or AS-ER (p < 0.05). Conclusion: BD bonded with RC demonstrated higher SBS than BD bonded with HVGIC. The failure mode in the RC group was predominantly cohesive, whereas in the HVGIC group, it was primarily adhesive. These findings support the clinical applicability of immediate definitive RC placement over BD using a methacryloyloxydecyl dihydrogen phosphate-containing adhesive with an etch-and-rinse strategy.
30 November 2025 in Restorative Dentistry & Endodontics
Objectives: This study evaluated the ability of calcium silicate cement (CSC) as a remineralizing agent compared with conventional glass ionomer cement (GIC) and resin-modified GIC (RMGIC) to remineralize artificial caries-affected dentin.Methods: Twenty-five class V cavities were prepared on extracted human third molars. Twenty teeth underwent artificial caries induction. The remaining five teeth with sound dentin serve as the positive control. The twenty demineralized teeth were subdivided into four groups (n = 5): carious dentin without restoration (negative control [NC]), carious dentin restored with CSC (Biodentine, Septodont), carious dentin restored with GI (Fuji IX, GC Corporation), and carious dentin restored with RMGIC (Fuji II LC, GC Corporation). Following restoration, the specimens were stored in artificial saliva for 7 days. The elastic modulus was evaluated by a nanoindentation test. The mineral composition was analyzed by scanning electron microscopy-energy-dispersive X-ray spectroscopy (SEM-EDX), and the mineral composition at the dentin-material interface.Results: CSC had a higher modulus of elasticity compared to GI, RMGI, and NC groups (p < 0.05). Higher calcium and phosphorus content was observed under CSC restorations, as indicated by SEM-EDX examination, which may lead to better remineralization.Conclusions: Compared to GI and RMGI, CSC showed the best remineralization and mechanical reinforcement in caries-affected dentin, indicating CSC for use in minimally invasive restorative dentistry.
Aerosol generation of respirable-fine particles during dental procedures with a high-speed handpiece represents a potential source of occupational particle exposure. Although removal of composite attachments in clear aligner therapy is frequently performed in clinics, its potential to generate aerosols remain underrecognized. This study aimed to quantify airborne particles generated by high-speed removal of composite attachments for clear aligners in a manikin model. Furthermore, the efficacy of three respiratory protection methods in reducing particle penetration was compared: a surgical mask alone (SM), a soft-silicone mask fitter combined with a surgical mask (SM + MF), and an N95 respirator (N95). Particle concentrations in the ambient environment during the high-speed removal of attachments were observed predominantly in the submicron size range of 0.30 to 0.99 µm ( p < 0.001). Overall, the N95 respirator provided the highest level of particle reduction, followed by the SM + MF and the SM alone. For particles larger than 0.25 µm, the SM + MF demonstrated substantial filtration improvements over the standard SM. Integrating a soft silicone mask fitter improves the facial seal of a surgical mask, demonstrating potential as a practical supplementary device to help mitigate aerosol exposure.
12 September 2026 in European Archives of Paediatric Dentistry