George G. Adams

George G. Adams

Auto-generated profile, based on publicly available information

George G. Adams

Department of Mechanical Engineering, Northeastern University, Boston, MA 02115

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2004 in Journal of Applied Mechanics
Verified
Journal Article
Closed access
PDF file
MNMikhail Nosonovsky
Mikhail Nosonovsky
GAGeorge G. Adams
George G. Adams

1 November 2014 in Royal Society Open Science
Verified
Journal Article
Open access
GAGeorge G. Adams
George G. Adams
The plane strain problem of a curved elastic body pressed against an elastic half-space is considered. The effect of adhesion is included through the use of surface energy in a manner similar to the well-known JKR theory for spherical contacts. The compressive normal force is held constant while a tangential force is gradually increased from zero. The contact is characterized by complete stick up to a critical value of the tangential force when there is a transition either directly to complete sliding or to a partial slip state in which a central stick region is surrounded by two slip regions. In the latter case, at a finite value of the stick zone width, a second critical condition exists at which there is a transition from partial slip to complete sliding. This behaviour is determined for a range of dimensionless values of the work of adhesion, the assumed constant shear stress during slip/sliding and the initial compressive load.

1 September 2014 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
ABAnirban Basu
Anirban Basu
RHRyan P Hennessy
Ryan P Hennessy
GAGeorge G Adams
George G Adams
NMNicol E McGruer
Nicol E McGruer

4 August 2008 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
LCL. Chen
L. Chen
NMN. E. McGruer
N. E. McGruer
GAG. G. Adams
G. G. Adams
YDY. Du
Y. Du
We report the observation of two distinct modes of rate-dependent behavior during contact cycling tests. One is a higher pull-off force at low cycling rates and the other is a higher pull-off force at high cycling rates. Subsequent investigation of these contacts using scanning electron microscopy (SEM) demonstrates that these two rate-dependent modes can be related to brittle and ductile separation modes. The former behavior is indicative of brittle separation, whereas the latter accompanies ductile separation. Thus by monitoring the rate dependence of the pull-off force, the type of separation mode can be identified during cycling without interrupting the test to perform SEM.

15 March 2008 in Journal of Applied Physics
Verified
Journal Article
Closed access
YDYan Du
Yan Du
GAGeorge G. Adams
George G. Adams
NMNicol E. McGruer
Nicol E. McGruer
IEIzhak Etsion
Izhak Etsion
A finite element model was developed to study adhesion of elastic-plastic microcontacts in a previous investigation. An interesting result was the identification of two distinct separation modes, i.e. brittle and ductile separation. In the current study, that model is used to conduct a series of simulations to determine the influence of four nondimensional parameters (including the maximum load parameter) on the contact and on the separation modes. The results show that the parameter S (the ratio of the theoretical stress to the hardness) and δf∕δc (representing the loading level) are the most important. Smaller S can only lead to brittle separation, while larger S can cause either separation mode depending on δf∕δc. Ductile separation is more likely to occur at smaller δf∕δc and brittle separation at greater δf∕δc. The transition between the two separation modes occurs at about S=1.2 (for δf∕δc=30) which corresponds to the theoretical stress for adhesion being 20% greater than the hardness. This result is qualitatively similar to the existing simplified analytical models, in that the adhesion energy, the hardness, and the loading level play important roles in the occurrence of ductile separation. However, there are important quantitative differences. Comparisons are also made with molecular dynamics simulations of a contact and with a fracture mechanics model of crack propagation.

1 July 2011 in Journal of Tribology
Verified
Journal Article
Closed access
PDF file
HEH. Eid
H. Eid
NJN. Joshi
N. Joshi
NMN. E. McGruer
N. E. McGruer
GAG. G. Adams
G. G. Adams
A finite element model of a layered hemisphere contacting a rigid flat, which includes the effect of adhesion, is developed. In this analysis elastic-plastic material properties were used for each of the materials comprising the layered hemisphere. The inclusion of the effect of adhesion, which was accomplished with the Lennard-Jones potential, required a special procedure. This configuration is of general theoretical interest in the understanding of adhesion. It has also been suggested as a possible design for a microswitch contact because, with an appropriate choice of metals, it has the potential to achieve low adhesion, low contact resistance, and high durability. The effect of the layer thickness on the adhesive contact was investigated. In particular the influences of layer thickness on the pull-off force, maximum contact radius, and contact resistance were determined. The results are presented as load versus interference and contact radius versus interference for loading and unloading from different values of the maximum interference.