1 October 2019 in Journal of Lightwave Technology
In-phase and quadrature (IQ) imbalances in optical transceiver, such as amplitude imbalance, phase imbalance, and IQ skew, can cause serious system performance degradation, especially when high order modulation formats are used. In this work, we present a method to isolate and separately monitor these various impairments from received signals by coherent digital signal processing (DSP). Receiver amplitude and phase imbalances could be compensated and monitored by Gram-Schmidt orthogonalization procedure (GSOP) and receiver skew could be compensated and monitored by a 4x4 or 4x2 multiple-input and multiple-output (MIMO) equalizer. Transmitter imperfections compensation and monitoring take place behind the residual frequency offset compensation and carrier phase recovery by a 4x4 MIMO equalizer based on minimal mean square error (MMSE) criterion. By these methods, we analyze and investigate the interaction of transceiver's impairments impact on each monitor numerically. After that, we conduct an experiment to verify the feasibility of the proposed method. All of these results show that each monitor could operate very robust even when multiple-impairments co-exist.
3 December 2024 in Journal of Lightwave Technology
In this paper, integrated scheme of enhanced vibration-sensing and digital subcarrier multiplexing (DSCM) communication based on frequency-domain pilot tones (FPTs) is proposed and demonstrated experimentally. In the scheme, FPTs are employed for multiple receiver digital signal processing (DSP) modules including frequency offset estimation (FOE), carrier phase estimation (CPE) and polarization demultiplexing. Meanwhile, with the recovered phase after CPE, the vibration-induced phase is extracted for sensing with band-pass filter within a frequency range of 7 kHz to 50 kHz. Thanks to two FPTs, dynamic FOE performance is enhanced under the frequency drift of 100 kHz ECLs compared to the conventional FOE methods, such as Max-Fast Fourier Transform (Max-FFT) and Viterbi-Viterbi (VV) algorithm. This enhancement can effectively suppress the background noise of the recovered phase after CPE, which inherently can subsequently improve the vibration sensing ability at a low frequency. In the experiment, sensing signal-to-noise ratio (SSNR) at 10 kHz is improved by 10 dB with the aid of FPTs. As a result, the vibration of frequency down to 10 kHz is successfully detected based on forward phase-based sensing in integrated DSCM communication system using commercial 100 kHz ECLs. The proposed integrated solution is compatible with the existing optical networks employing commercial ECLs to support intelligent operation and maintenance.
10 May 2024 in Journal of Lightwave Technology
Directly modulated lasers (DMLs) have been implemented in short-reach optical networks as an intensity modulation and direct detection (IM-DD) scheme due to their high output power, small footprint, and low-cost fabrication. However, the attainable data rate of C-band DML-based IM-DD systems faces limitations imposed by the DML bandwidth, power fading due to chromatic dispersion, and nonlinear impairments resulting from the interplay between frequency chirp and chromatic dispersion. In this paper, we propose a joint sparse Volterra nonlinear equalization (SVNE) and gradient-descent noise whitening (GD-NW) digital signal processing technique to effectively mitigate the overall impairments. Through experimental verification, we achieve, to the best of our knowledge, the highest net data rates of 142.3/143/134.6/102.8/73.7/61.4 Gb/s over 0/5/10/20/40/60 km standard single-mode fiber for C-band DML-based IM-DD links, with the help of the proposed technique. Compared with previous works, our approach leads to an increase in transmission capacity by at least 10%. Furthermore, we conduct a comprehensive investigation into the achieved net data rate considering various factors, including modulation format, peak-to-peak voltage of the electrical output, utilization of the electrical amplifier, transmission reaches and different application scenarios, DML's chirp and extinction ratio, and the roll-off factor of the pulse shaping filter. Detailed guidelines are provided for performance-oriented efficient operations and measurements of DML-based IM-DD links.