Martin Petkovšek

Martin Petkovšek

Auto-generated profile, based on publicly available information

Martin Petkovšek

Faculty of Mechanical Engineering, University of Ljubljana, Ljubljana, Slovenia

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2015 in Ultrasonics Sonochemistry
Verified
Journal Article
Open access
MPMartin Petkovšek
Martin Petkovšek
MMMatej Mlakar
Matej Mlakar
MLMarjetka Levstek
Marjetka Levstek
MSMarjeta Stražar
Marjeta Stražar
BŠBrane Širok
Brane Širok
MDMatevž Dular
Matevž Dular
The disintegration of raw sludge is very important for enhancement of the biogas production in anaerobic digestion process as it provides easily degradable substrate for microorganisms to perform maximum sludge treatment efficiency and stable digestion of sludge at lower costs. In the present study the disintegration was studied by using a novel rotation generator of hydrodynamic cavitation (RGHC). At the first stage the analysis of hydrodynamics of the RGHC were made with tap water, where the cavitation extent and aggressiveness was evaluated. At the second stage RGHC was used as a tool for pretreatment of a waste-activated sludge (WAS), collected from wastewater treatment plant (WWTP). In case of WAS the disintegration rate was measured, where the soluble chemical oxygen demand (SCOD) and soluble Kjeldahl nitrogen were monitored and microbiological pictures were taken. The SCOD increased from initial 45 mg/L up to 602 mg/L and 12.7% more biogas has been produced by 20 passes through RGHC. The results were obtained on a pilot bioreactor plant, volume of 400 L.

6 September 2022 in Ultrasonics Sonochemistry
Verified
Journal Article
Open access
GKGregor Kozmus
Gregor Kozmus
JZJure Zevnik
Jure Zevnik
MHMarko Hočevar
Marko Hočevar
MDMatevž Dular
Matevž Dular
MPMartin Petkovšek
Martin Petkovšek
• Acoustic cavitation is investigated at various ambient pressures. • Immersion depth of the horn affects power consumption but not cavitation size. • Cavitation size grows with increasing salinity but is reduced in saturated solution. • A novel parameter for acoustic cavitation is proposed.

31 January 2022 in Biomacromolecules
Verified
Journal Article
Open access
JRJakob D. Redlinger-Pohn
Jakob D. Redlinger-Pohn
MPMartin Petkovšek
Martin Petkovšek
KGKorneliya Gordeyeva
Korneliya Gordeyeva
MZMojca Zupanc
Mojca Zupanc
AGAlisa Gordeeva
Alisa Gordeeva
DSDaniel L Söderberg
Daniel L Söderberg
Cellulose fibrils are the structural backbone of plants and, if carefully liberated from biomass, a promising building block for a bio-based society. The mechanism of the mechanical release─fibrillation─is not yet understood, which hinders efficient production with the required reliable quality. One promising process for fine fibrillation and total fibrillation of cellulose is cavitation. In this study, we investigate the cavitation treatment of dissolving, enzymatically pretreated, and derivatized (TEMPO oxidized and carboxymethylated) cellulose fiber pulp by hydrodynamic and acoustic (i.e., sonication) cavitation. The derivatized fibers exhibited significant damage from the cavitation treatment, and sonication efficiently fibrillated the fibers into nanocellulose with an elementary fibril thickness. The breakage of cellulose fibers and fibrils depends on the number of cavitation treatment events. In assessing the damage to the fiber, we presume that microstreaming in the vicinity of imploding cavities breaks the fiber into fibrils, most likely by bending. A simple model showed the correlation between the fibrillation of the carboxymethylated cellulose (CMCe) fibers, the sonication power and time, and the relative size of the active zone below the sonication horn.

1 November 2019 in Ultrasonics Sonochemistry
Verified
Journal Article
Closed access
MPMartin Petkovšek
Martin Petkovšek
MDMatevž Dular
Matevž Dular

1 October 2020 in Ultrasonics Sonochemistry
Verified
Journal Article
Open access
MPMartin Petkovšek
Martin Petkovšek
MHMatej Hočevar
Matej Hočevar
PGPeter Gregorčič
Peter Gregorčič
The interaction between liquid flow and solid boundary can result in cavitation formation when the local pressure drops below vaporization threshold. The cavitation dynamics does not depend only on basic geometry, but also on surface roughness, chemistry and wettability. From application point of view, controlling cavitation in fluid flows by surface functionalization is of great importance to avoid the unwanted effects of hydrodynamic cavitation (erosion, noise and vibrations). However, it could be also used for intensification of various physical and chemical processes. In this work, the surfaces of 10-mm stainless steel cylinders are laser textured in order to demonstrate how hydrodynamic cavitation behavior can be controlled by surface modification. The surface properties are modified by using a nanosecond (10-28 ns) fiber laser (wavelength of 1060 nm). In such a way, surfaces with different topographies and wettability were produced and tested in a cavitation tunnel at different cavitation numbers (1.0-2.6). Cavitation characteristics behind functionalized cylindrical surfaces were monitored simultaneously by high-speed visualization (20,000 fps) and high frequency pressure transducers. The results clearly show that cavitation characteristics differ significantly between different micro-structured surfaces. On some surfaces incipient cavitation is delayed and cavitation extent decreased in comparison with the reference - a highly polished cylinder. It is also shown that the increased surface wettability (i.e., hydrophilicity) delays the incipient cavitation.

1 May 2015 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
JWJian Wang
Jian Wang
MPMartin Petkovšek
Martin Petkovšek
HLHoulin LIU
Houlin LIU
BŠBrane Širok
Brane Širok
MDMatevž Dular
Matevž Dular
We are comparing results of numerical simulations against high-speed simultaneous observations of cavitation and cavitation erosion. We performed fully compressible, cavitating flow simulations to resolve the formation of the shock waves at cloud collapse—these are believed to be directly related to the formation of the damage. Good agreements were noticed between calculations and tests. Two high pressure peaks were found during one cavitation cycle. One relates to the cavitation collapse and the other one corresponds to the cavitation shed off, both contributing to a distinctive stepwise erosion damage growth pattern. Additional, more precise, simulations with much shorter time step were performed to investigate the processes of cavitation collapse and shedding off in more detail. There the importance of small cavitation structures which collapse independently of the main cloud was found. The present work shows a great potential for future development of techniques for accurate predictions of cavitation erosion by numerical means only.