Approaches to boost the efficiency and stability of perovskite solar cells often address one singular problem in a specific device configuration. In this work, we utilize a poly(ionic liquid) (PIL) to introduce a multi-functional interlayer to improve the device efficiency and stability for different perovskite compositions and architectures. The presence of the PIL at the perovskite surface reduces the non-radiative losses down to 60 meV already in the neat material, indicating effective surface trap passivation, thereby pushing the external photoluminescence quantum yield up to 7%. In devices, the PIL treatment induces a bi-functionality of the surface where insulating areas act as a blocking layer reducing interfacial charge recombination and increasing the VOC, whereas, at the same time, the passivated neighbouring regions provide more efficient charge extraction, increasing the FF. As a result, these solar cells exhibit outstanding VOC and FF values of 1.17 V and 83% respectively, with the best devices reaching conversion efficiencies up to 21.4%. The PIL-treated devices additionally show enhanced stability during maximum power point tracking (>700 h) and unchanged efficiencies after 10 months of shelf storage. By applying the PIL to small and wide bandgap perovskites, and to nip cells, we corroborate the generality of this methodology to improve the efficiency in various cell architectures and perovskite compositions.
This work presents results from high-resolution scanning transmission electron microscopy and electron energy-loss spectroscopy on twin boundaries (TBs) and nontwin grain boundaries (GBs) in Cu(In,Ga)Se2 thin films. It is shown that the atomic reconstruction is different for different symmetries of the grain boundaries. We are able to confirm the model proposed by Persson and Zunger [Phys. Rev. Lett. 91, 266401 (2003)] for Se-Se-terminated $\Sigma${}3 {112} TBs, showing Cu depletion and In enrichment in the two atomic planes closest to the TB. On the contrary, Cu depletion without In enrichment is detected for a cation-Se-terminated TB. At nontwin GBs, always a strong anticorrelation of Cu and In signals is detected suggesting that the formation of InCu or CuIn antisites within a very confined region of smaller than 1~nm is an essential element in the reconstruction of these GBs.
Wide bandgap halide perovskite materials show promising potential to pair with silicon bottom cells. To date, most efficient wide bandgap perovskites layers are fabricated by spin-coating, which is difficult to scale up. Here, we report on slot-die coating for an efficient, 1.68 eV wide bandgap triple-halide (3halide) perovskite absorber, (Cs0.22FA0.78)Pb(I0.85Br0.15)3 + 5 mol % MAPbCl3. A suitable solvent system is designed specifically for the slot-die coating technique. We demonstrate that our fabrication route is suitable for tandem solar cells without phase segregation. The slot-die coated wet halide perovskite is dried by a "nitrogen (N2)-knife" with high reproducibility and avoiding antisolvents. We explore varying annealing conditions and identify parameters allowing crystallization of the perovskite film into large grains reducing charge collection losses and enabling higher current density. At 150 °C, an optimized trade-off between crystallization and the PbI2 aggregates on the film's top surface is found. Thus, we improve the cell stability and performance of both single-junction cells and tandems. Combining the 3halide top cells with a 120 μm thin saw damage etched commercial Czochralski industrial wafer, a 2-terminal monolithic tandem solar cell with a PCE of 25.2% on a 1 cm2 active area is demonstrated with fully scalable processes.
A new method for enhancing the charge separation and photo‐electrochemical stability of CuBi2O4 photoelectrodes by sequentially depositing Bi2O3 and CuO layers on fluorine‐doped tin oxide substrates with pulsed laser deposition (PLD), followed by rapid thermal processing (RTP), resulting in phase‐pure, highly crystalline films after 10 min at 650 °C, is reported. Conventional furnace annealing of similar films for 72 h at 500 °C do not result in phase‐pure CuBi2O4. The combined PLD and RTP approach allow excellent control of the Bi:Cu stoichiometry and results in photoelectrodes with superior electronic properties compared to photoelectrodes fabricated through spray pyrolysis. The low photocurrents of the CuBi2O4 photocathodes fabricated through PLD/RTP in this study are primarily attributed to their low specific surface area, lack of CuO impurities, and limited, slow charge transport in the undoped films. Bare (without protection layers) CuBi2O4 photoelectrodes made with PLD/RTP shows a photocurrent decrease of only 26% after 5 h, which represents the highest stability reported to date for this material. The PLD/RTP fabrication approach offers new possibilities of fabricating complex metal oxides photoelectrodes with a high degree of crystallinity and good electronic properties at higher temperatures than the thermal stability of glass‐based transparent conductive substrates would allow.
Thin-film solar cells based on polycrystalline absorbers have reached very high conversion efficiencies of up to 23-25%. In order to elucidate the limiting factors that need to be overcome for even higher efficiency levels, it is essential to investigate microscopic origins of loss mechanisms in these devices. In the present work, a high efficiency (21% without anti-reflection coating) copper indium gallium diselenide (CIGSe) solar cell is characterized by means of a correlative microscopy approach and corroborated by means of photoluminescence spectroscopy. The values obtained by the experimental characterization are used as input parameters for two-dimensional device simulations, for which a real microstructure was used. It can be shown that electrostatic potential and lifetime fluctuations exhibit no substantial impact on the device performance. In contrast, nonradiative recombination at random grain boundaries can be identified as a significant loss mechanism for CIGSe solar cells, even for devices at a very high performance level.