We present a data-based model for low mode asymmetry in low gas-fill hohlraum experiments on the National Ignition Facility {NIF [Moses et al., Fusion Sci. Technol. 69, 1 (2016)]} laser. This model is based on the hypothesis that the asymmetry in these low fill hohlraums is dominated by the hydrodynamics of the expanding, low density, high-Z (gold or uranium) “bubble,” which occurs where the intense outer cone laser beams hit the high-Z hohlraum wall. We developed a simple model which states that the implosion symmetry becomes more oblate as the high-Z bubble size becomes large compared to the hohlraum radius or the capsule size becomes large compared to the hohlraum radius. This simple model captures the trends that we see in data that span much of the parameter space of interest for NIF ignition experiments. We are now using this model as a constraint on new designs for experiments on the NIF.
1 October 2010 in Review of Scientific Instruments
Ignition of imploding inertial confinement capsules requires, among other things, controlling the symmetry with high accuracy and fidelity. We have used gated x-ray imaging, with 10 μm and 70 ps resolution, to detect the x-ray emission from the imploded core of symmetry capsules at the National Ignition Facility. The measurements are used to characterize the time dependent symmetry and the x-ray bang time of the implosion from two orthogonal directions. These measurements were one of the primary diagnostics used to tune the parameters of the laser and Hohlraum to vary the symmetry and x-ray bang time of the implosion of cryogenically cooled ignition scale deuterium/helium filled plastic capsules. Here, we will report on the successful measurements performed with up to 1.2 MJ of laser energy in a fully integrated cryogenics gas-filled ignition-scale Hohlraum and capsule illuminated with 192 smoothed laser beams. We will describe the technique, the accuracy of the technique, and the results of the variation in symmetry with tuning parameters, and explain how that set was used to predictably tune the implosion symmetry as the laser energy, the laser cone wavelength separation, and the Hohlraum size were increased to ignition scales. We will also describe how to apply that technique to cryogenically layered tritium-hydrogen-deuterium capsules.
Symmetry of an implosion is crucial to get ignition successfully. Several methods of control and measurement of symmetry have been applied on many laser systems with mm size hohlraums and ns pulses. On the National Ignition Facility [Moses et al., Phys. Plasmas 16, 041006 (2009)] we have large hohlraums of cm scale, long drive pulses of 10 s of ns, and a large number of beams with the option to tune their wavelengths. Here we discuss how we used the x-ray self-emission from imploding surrogates to ignition capsules (symcaps) to measure the symmetry of the implosion. We show that symcaps are good surrogates for low order symmetry, though having lower sensitivity to distortions than ignition capsules. We demonstrate the ability to transfer energy between laser beams in a gas-filled hohlraum using wavelength tuning, successfully tuning the lowest order symmetry of the symcaps in different size hohlraums at different laser energies within the specification established by calculations for successful ignition.
We report on a high convergence ratio liquid layer capsule implosion performed on the National Ignition Facility and contrast it to two previously reported layered implosions, in order to better understand how the capsule design impacts the hydrodynamic stability properties of implosions. Three implosions were performed with similar convergence ratios, fuel entropy, in-flight aspect ratios, and unablated shell mass; these qualities are important for determining hydrodynamic stability. Nevertheless, while two of these implosions exhibited robustness to asymmetries, including our recent experiment that had abnormally large amplitude long-wavelength capsule asymmetries, and produced more than 80% or the yield predicted by one-dimensional (1D) simulations, which do not account for the impacts of hydrodynamic instabilities, the third implosion produced only 14% of the yield from a 1D simulation. We perform a detailed computational analysis of these three shots, which suggests that the combination of several large asymmetry seeds result in the significantly degraded performance: a large 30 μm fill tube, the presence of a microstructure in the high density carbon ablator, and a higher level of drive asymmetry. This indicates that while it is possible to stabilize a high convergence ratio implosion through various means, the factors that determine stability cannot be considered independently. Furthermore, when these asymmetries are combined in 2D simulations, they can exhibit destructive interference and underpredict the yield degradation compared to experiment and three-dimensional simulations.
The dilation x-ray imager (DIXI) [T. J. Hilsabeck et al., Rev. Sci. Instrum. 81, 10E317 (2010); S. R. Nagel et al., ibid. 83, 10E116 (2012); S. R. Nagel et al., ibid. 85, 11E504 (2014)] is a high-speed x-ray framing camera that uses the pulse-dilation technique to achieve a temporal resolution of less than 10 ps. This is a 10 × improvement over conventional framing cameras currently employed on the National Ignition Facility (NIF) (100 ps resolution), and otherwise only achievable with 1D streaked imaging. A side effect of the dramatically reduced gate width is the comparatively lower detected signal level. Therefore we implement a Poisson noise reduction with non-local principal component analysis method [J. Salmon et al., J. Math. Imaging Vision 48, 279294 (2014)] to improve the robustness of the DIXI data analysis. Here we present results on ignition-relevant experiments at the NIF using DIXI. In particular we focus on establishing that/when DIXI gives reliable shape metrics (P0, P2, and P4 Legendre modes, and their temporal evolution/swings).
Many inertial fusion designs use capsules made of beryllium, as its high mass ablation rate is advantageous. We present the first systematic experimental study of indirectly driven beryllium capsules with a cryogenic deuterium-tritium fuel layer. “Subscale” capsules, 80% of the nominal National Ignition Facility point design radius, show optimal performance with the remaining mass of ∼6–7%. A buoyancy-drag mix model explains the implosion performance, suggesting that fuel-ablator mix is the dominant degradation mechanism. Increasing the capsule scale is predicted to reduce the impact of fuel-ablator mix and achieve high performance.