Eryk Mączka

Dr. Eryk Mączka

Wrocław University of Science and Technology, Wrocław, Dolnośląskie, Poland
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 March 2021 in Materials
Verified
Journal Article
Open access
PDF file
Piotr MackiewiczPiotr Mackiewicz
Piotr Mackiewicz
Eryk MączkaEryk Mączka
Eryk Mączka
An original experimental method was used to investigate the influence of water and road salt with anti-caking agent on the material used in pavement construction layers. This method allowed for monitoring material changes resulting from the influence of water and road salt with anti-caking agent over time. The experiment used five different mineral road mixes, which were soaked separately in water and brine for two time intervals (2 days and 21 days). Then, each sample of the mix was subjected to tests of the complex module using the four-point bending (4PB-PR) method. The increase in mass of the soaked samples and the change in value of the stiffness modulus were analyzed. Exemplary tomographic (X-ray) imaging was performed to confirm the reaction of the road salt and anti-caking agent (lead agent) with the material. Based on measurements of the stiffness modulus and absorption, the correlations of the mass change and the value of the stiffness modulus were determined, which may be useful in estimating the sensitivity of mixes to the use of winter maintenance agents—e.g., road salt with anti-caking agent (sodium chloride). It was found that the greatest changes occur for mixes intended for base course layers (mineral cement mix with foamed asphalt (MCAS) and mineral-cement-emulsion mixes (MCE)) and that the smallest changes occur for mixes containing highly modified asphalt (HIMA).

20 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
Eryk MączkaEryk Mączka
Eryk Mączka
Piotr MackiewiczPiotr Mackiewicz
Piotr Mackiewicz
The pavement structure during the colder seasons (winter) or in regions located above sea level is commonly affected and deteriorated by many environmental factors. Two prominent factors are water and frost (weather) or road salt (maintenance). According to the article’s literature review, there are only a few studies related to water and frost or road salt impact on mineral asphalt mixes considering fatigue. Most of the tests were performed on mixes containing common road asphalt or only one binder content level was investigated. There are no articles that investigate this problem comprehensively including new asphalt, its content levels, or production technology. Based on the literature review, the main problem regarding degradation impact on mixtures fatigue life was stated. The investigation was performed using two proprietary experimental methods allowing approximates in situ conditions regarding environmental impacts. A dynamic four-point bending fatigue test was applied to evaluate degradation considering fatigue. The investigation was performed using four coarse-graded asphalt mixtures (asphalt concrete AC 22) which differed in binder type (35/50 WMA, 35/50, 25/55-60, and 25/55-80 HIMA), content level (4.24%, 4.03%, 3.82%), and production technology (hot and warm). Regarding the results obtained, the authors proposed a degradation ratio regarding fatigue life variability. Based on the obtained results and ratio used, it was found that both interactions caused a significant fatigue life decrease—in the worst case, over tens of percent. Furthermore, it was found that asphalt mixture resistance to environmental factors depends on binder type, its content level, air void content, and discussed impact. Moreover, asphalt mixtures’ susceptibility to degradation (fatigue) is extreme at lower binder content levels and accelerates due to air void content increase. In the article, it was also stated that the highest resistance was reached by a mixture with highly modified asphalt (25/55-80 HIMA). It was also found that the SBS polymer dosage increase in the asphalt matrix enhances asphalt mixture resistance to environmental impacts. The least resistant to the environmental degradation mixture was WMA (35/50 WMA).

25 November 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Eryk MączkaEryk Mączka
Eryk Mączka
Piotr MackiewiczPiotr Mackiewicz
Piotr Mackiewicz
Water, frost, and road salt are counted as environmental factors. They affect the pavement structure, particularly during the winter or in regions located above sea level. In the article, a literature review related to water, frost, and road salt impacts was performed. The main problem of evaluating asphalt mixture degradation and its influence on pavement fatigue life via environmental factors was stated. Four types of asphalt concrete (AC22) road mixes were prepared for laboratory tests. They differed in production technology and the type of binder applied. One binder content level was tested. To investigate the impact of water, frost, and road salt on mineral-asphalt mixtures utilized in flexible constructions, two proprietary experimental methods were applied. Methods allowed for determining the mixtures’ degradation level using the measured stiffness modulus in the 4-PB-PR test. Based on the obtained results, it was found that both interactions cause a significant decrease in the value of the stiffness modulus. In the article, a degradation ratio was proposed. The ratio expressed the impact of water, frost, and road salt on the stiffness mix variability. Its value was considered for pavement fatigue life based on the AASHTO 2004 fatigue criterion. The article demonstrates that the type of binder used influences the mix’s resistance to water, frost, or road salt impact. The highest resistance was reached by a mixture with highly modified asphalt (hot technology), and the worst was with asphalt WMA (warm technology). It has also been proven that the impact of water, frost, or road salt on pavement fatigue life is significant. The drop was significant, amounting to a few dozen percent. It was stated that environmental impacts (such as water, frost, or road salt) should be considered in asphalt mixture and pavement construction design.

22 February 2023 in Road Materials and Pavement Design
Verified
Journal Article
Open access
Eryk MączkaEryk Mączka
Eryk Mączka
Piotr MackiewiczPiotr Mackiewicz
Piotr Mackiewicz
Water, frost, and road salt are important environmental factors that affect the durability of the entire pavement structure e.g. during the winter season or in regions located above sea zones. A proprietary experimental method was used to investigate the influence of these factors on mineral asphalt mixtures. Four road mix types of asphalt concrete (AC22) were analysed in the experiment. They differed in production technology, type, and content of the binder used. Based on the experimental approach and test data, changes in the value of the initial stiffness modulus (4-PB-PR test) were analysed. Based on the obtained results, it was established that both interactions caused a significant decrease in the module's value, which reached over a dozen percent. The article also evidenced that lower binder content in mixtures increases the negative environmental impact on the material, whereas its type may accelerate or reduce material degradation.

1 January 2019 in BUILDER
Verified
Journal Article
Closed access
Eryk MączkaEryk Mączka
Eryk Mączka
TEST OF MINERAL ASPHALT MIXTURES IN THE STATIC FOUR POINTBENDING TEST AT TEMPERATURE 25°C The article presents an experimental method for testing beams made of AC16W mineralasphalt mix in a static four-point bending test. Tests were performed at a fixed measuring temperature of 25°C and for different load levels. The conditions of the study that specify the variable characteristics of asphalt mixtures were specified. Attention was paid to the material specificity of the mixturesand the variability of the stiffness modulus was analyzed. Different ways of its determination with different load cycles are presented. The obtained results of the modules were compared with the results obtained in the dynamic test. The identification of the secant modulus from the dependence of the load curve between strain and stress for the first cycle was indicated.

1 November 2018 in Transportation Overview - Przeglad Komunikacyjny
Verified
Journal Article
Closed access
Eryk MączkaEryk Mączka
Eryk Mączka
The article presents an issue related to the phenomenon of regeneration occurring in mineral-asphalt mixtures. The introduction of the work discusses the problem of decreasing strength and fatigue life of asphalt mixtures expressed by changing the stiffness modulus. Attention is paid to the complexity of this phenomenon, which is associated with microstructural changes. The review of the state of knowledge discusses a phenomenon called "healing" referring directly to the regeneration of mineral-asphalt mixtures. Later on, based on fatigue tests of the four-point bending beam in the controlled deformation mode, this phenomenon was analyzed. Rest periods between load and heating of samples regenerating the tested mixture are taken into account. Based on the analysis of the test results, it was found that the heating process is a more effective factor leading to a greater regeneration gain not only the stiffness of the sample, but also its lifespan expressed in cycles compared to the rest period. At the end of the work, hysteresis changes were shown to analyze energy changes and the essence of regenerative processes in the context of extending the life of mineral asphalt mixes used in the pavement construction layers.