Ivan Radaš

Mr. Ivan Radaš

Faculty of Electrical Engineering and Computing, Zagreb, Zagreb, Grad, Croatia
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2025 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
MMMotalleb Miri
Motalleb Miri
IRIvan Radaš
Ivan Radaš
Ivan ToljIvan Tolj
Ivan Tolj
FBFrano Barbir
Frano Barbir

23 April 2021 in Energies
Verified
Journal Article
Open access
PDF file
IRIvan Radaš
Ivan Radaš
IŽIvan Župan
Ivan Župan
VŠViktor Šunde
Viktor Šunde
ŽBŽeljko Ban
Željko Ban
Electric trams are one of the standard forms of public transport. They are characterized by large amounts of electric current and electric current gradient from the power grid, especially during acceleration. For this reason, a regenerative braking system is considered with the aim of reducing electric current peaks and increasing energy efficiency by reducing the total energy consumption of the power grid. A supercapacitor module is used as a storage device for storing and utilizing the braking energy. The supercapacitor module and the power grid constitute a hybrid energy system, for which a control algorithm has been developed. The control algorithm takes into account the influence of the elevation profile and the slope of the vehicle route in storing and using the braking energy. The operation of the algorithm was simulated and analyzed using the MATLAB/Simulink software package for tram lines with different elevation profiles.

17 February 2024 in Processes
Verified
Journal Article
Open access
PDF file
IRIvan Radaš
Ivan Radaš
LMLuka Matić
Luka Matić
VŠViktor Šunde
Viktor Šunde
ŽBŽeljko Ban
Željko Ban
This paper proposes a new method for assessing the state of charge (SoC) and identifying the types of different lithium-ion cells used in the battery systems of light electric vehicles. A particular challenge in the development of this method was the SoC estimation time, as the method is intended for implementation in the control system of a bicycle charging station, where the state of charge must be determined immediately after the bicycle is plugged in in order to start the charging process as quickly as possible according to the appropriate charging algorithm. The method is based on the identification of the transfer function, i.e., the dynamic response of the battery voltage to the current pulse. In the learning phase of this method, a database of reference transfer functions and corresponding SoCs for a specific type of battery cell is created. The transfer functions are described by coefficients determined through the optimization procedure. The algorithm for estimating the unknown battery cell SoCs is based on the comparison of the measured voltage response with the responses of the reference transfer functions from the database created during the learning process to the same current signal. The comparison is made by calculating the integral of the square error (ISE) between the response of the specific reference transfer function and the measured voltage response of the battery cell. Each transfer function corresponds to a specific SoC and cell type. The specific SoC of the unknown battery is determined by quadratic interpolation of the SoC near the reference point with the smallest ISE for each battery type. The cell type detection algorithm is based on the fact that the integral squared error criterion near the actual SoC for the actual cell type changes less than the squared error criterion for any other battery cell type with the same SoC. An algorithm for estimating the SoC and cell type is described and tested on several different cell types. The relative error between the estimated SoC and the actual SoC was used as a measure of the accuracy of the algorithm, where the actual SoC was calculated using the Coulomb counting method.

6 September 2022 in Energies
Verified
Journal Article
Open access
PDF file
IRIvan Radaš
Ivan Radaš
NPNicole Pilat
Nicole Pilat
DGDaren Gnjatović
Daren Gnjatović
VŠViktor Šunde
Viktor Šunde
ŽBŽeljko Ban
Željko Ban
There are several methods for estimating the SoC of lithium-ion batteries that use electrochemical battery models or artificial intelligence and intelligent algorithms. These methods have numerous advantages but are complex and computationally intensive. This paper presents a new method for estimating the SoC of lithium-ion batteries based on identifying the transfer function of the measured battery voltage response to the charging current pulse. It is assumed that the transfer function of the battery changes with the state of charge. In the learning phase, a reference table of known SoCs and associated transfer functions is created. The parameters of these transfer functions form the reference points in hyperspace. In the phase of determining the unknown SoC of the battery, the parameters of the measured transfer function form a point in hyperspace that is compared with the reference points of the transfer functions for known SoCs. The unknown SoC of the battery at the particular measurement time is obtained by finding the two reference points closest to the point of unknown SoC using the Euclidean distance and a linear interpolation based on this distance. The method is simple, computationally undemanding, insensitive to measurement noise, and has high accuracy in SoC estimation.