The global economic growth, the increase in the population, and advances in technology lead to an increment in the global primary energy demand. Considering that most of this energy is currently supplied by fossil fuels, a considerable amount of greenhouse gases are emitted, contributing to climate change, which is the reason why the next European Union binding agreement is focused on reducing carbon emissions using hydrogen. This study reviews different technologies for hydrogen production using renewable and non-renewable resources. Furthermore, a comparative analysis is performed on renewable-based technologies to evaluate which technologies are economically and energetically more promising. The results show how biomass-based technologies allow for a similar hydrogen yield compared to those obtained with water-based technologies but with higher energy efficiencies and lower operational costs. More specifically, biomass gasification and steam reforming obtained a proper balance between the studied parameters, with gasification being the technique that allows for higher hydrogen yields, while steam reforming is more energy-efficient. Nevertheless, the application of hydrogen as the energy vector of the future requires both the use of renewable feedstocks with a sustainable energy source. This combination would potentially produce green hydrogen while reducing carbon dioxide emissions, limiting global climate change, and, thus, achieving the so-called hydrogen economy.
Hydrogen obtained from biomass derivatives is considered a promising alternative to fossil fuels. The aim of this work is to test the viability of Ni-M/SBA-15 (M: Co, Cu, Cr) catalysts for the hydrogen production from bio-oil aqueous fraction reforming. Tests were performed in a fixed-bed reactor at 600 °C and atmospheric pressure. Firstly, the steam reforming (SR) of acetic acid, hydroxyacetone, furfural and phenol, as representative constituents of the bio-oil aqueous fraction, was carried out. Lower reactivity with increasing carbon number and decreasing steam-to-carbon ratio was observed. Coking rate during SR is a consequence of carbon number and aromaticity of the reactant, as well as the steam-to-carbon ratio. However, deactivation also depends on the graphitization degree of carbon filaments, higher in the case of coke formed from phenol. Then, the performance of the Ni-M/SBA-15 catalysts was studied in the reforming of a bio-oil aqueous fraction surrogate containing the four model compounds. Ni-Co/SBA-15 and Ni-Cr/SBA-15 samples were the most active because Co also catalyze the steam reforming reactions and Cr promotes the formation of very small Ni crystallites accounting for high conversion and the low coke deposition (~8 times lower than Ni/SBA-15) in the form of poorly condensed carbon filaments.
Hydrogen production derived from thermochemical processing of biomass is becoming an interesting alternative to conventional routes using fossil fuels. In this sense, steam reforming of the aqueous fraction of microalgae hydrothermal liquefaction (HTL) is a promising option for renewable hydrogen production. Since the HTL aqueous fraction is a complex mixture, acetic acid has been chosen as model compound. This work studies the modification of Co/SBA-15 catalyst incorporating a second metal leading to Co-M/SBA-15 (M: Cu, Ag, Ce and Cr). All catalysts were characterized by N2 physisorption, ICP-AES, XRD, TEM, H2-TPR, H2-TPD and Raman spectroscopy. The characterization results evidenced that Cu and Ag incorporation decreased the cobalt oxides reduction temperatures, while Cr addition led to smaller Co0 crystallites better dispersed on the support. Catalytic tests done at 600 °C, showed that Co-Cr/SBA-15 sample gave hydrogen selectivity values above 70 mol % with a significant reduction in coke deposition.
Oxidative steam reforming allows higher energy efficiency and lowers coke deposition compared to traditional steam reforming. In this work, CeO2-based supports have been prepared with Ni as the active phase, and they were tested in the oxidative steam reforming of acetic acid. The influence of the O2/AcOH molar ratio (0–0.3) has been evaluated over Ni/CeO2. The results stated that by increasing oxygen content in the feeding mixture, acetic acid conversion increases, too, with a decrease in coke deposition and hydrogen yield. To have a proper balance between the acetic acid conversion and the hydrogen yield, an O2/AcOH molar ratio of 0.075 was selected to study the catalytic performance of Ni catalysts over different supports: commercial CeO2, a novel mesostructured CeO2, and CeO2-SBA-15. Due to higher Ni dispersion over the support, the mesostructured catalysts allowed higher acetic acid conversion and hydrogen yield compared to the nonporous Ni/CeO2. The best catalytic performance and the lowest coke formation (120.6 mgcoke·gcat−1·h−1) were obtained with the mesostructured Ni/CeO2. This sample reached almost complete conversion (>97%) at 500 °C, maintaining the hydrogen yield over 51.5% after 5 h TOS, being close to the predicted value by the thermodynamic equilibrium that is due to the synergistic coordination between Ni and CeO2 particles.
1 June 2020 in International Journal of Hydrogen Energy