This paper examines the impact of salinity on the thermophysical properties of soils during artificial freezing. It focuses on analyzing heat and mass transfer in saline soils for constructing a frozen wall around a mineshaft at a potash salt deposit. The presence of salts in the groundwater near the contact point with water-protective strata is common in these deposits. Experimental studies were conducted on clay, chalk, and sand to understand the effect of salinity on the freezing temperature, unfrozen water content, specific heat capacity, and thermal conductivity of wet soil. These findings were used to simulate heat and mass transfer in saline soils using a one-dimensional model. The technique of circumferential averaging was introduced to account for the thermal impact of freeze pipes. The results indicate that higher soil salinity leads to a faster decrease in soil temperature under freezing conditions, although this dependence is weak for clay. This study also revealed that an increase in initial salinity results in a reduction in the thickness of the frozen wall. It was found that, for chalk and sand, there exists a range of initial salinity during which the frozen wall’s thickness is almost independent of the initial salinity.
19 January 2024 in International Journal of Thermal Sciences
The article describes the results of laboratory studies on the unfrozen water content and ultimate long-term strength of frozen clay and chalk samples in the temperature range from −10 to −25 °C. The soil samples contained dissolved salt in the pore space, with three types of salts (NaCl, KCl, and CaCl2) being considered. The findings indicate that the influence of the content and type of dissolved salt on the ultimate long-term strength of soils is realized indirectly through the unfrozen water content. In this case, the soil freezing characteristic curve in the region of negative temperatures significantly depends on both the type of dissolved salt and its quantity. The experimental data obtained were used to parameterize the model and calculate the maximum bearing capacity of the frozen wall (FW) in the presence of dissolved salts in the volume of frozen soils. It has been demonstrated that the decrease in the maximum FW bearing capacity is substantial with the appearance of dissolved salt in the pore space of the soils. This decrease is at-tributed to the combined effects of two factors: 1) a reduction in the FW thickness and 2) a decrease in the frozen soil strength due to an increase in the amount of unfrozen water content in the soil pore space. The second factor is deemed more significant.
1 March 2021 in Mathematical Models and Computer Simulations
The paper is devoted to the simulation of oil displacement by water and the formation of the Saffman–Taylor instability. The problem is solved in two-dimensional formulation. A circular domain with one injection well and eight production wells located along the contour around the injection well is considered as geometry. To study the patterns of oil displacement by water, hydrostatic pressure, oil and water seepage rates, and oil saturation are calculated. The graphical analysis considers mainly the oil saturation field. The hydrostatic pressure field is calculated by solving the steady-state piezoconductivity equation; the field of the oil-water seepage rate is calculated using the linear Darcy filtration law; and the oil saturation field is calculated from the solution of the advection transport equation. The two-phase nature of the flow considered in the problem lies in the fact that the oil and water phases have their own relative phase permeabilities calculated using the Brooks–Corey model. The equations are solved numerically using the finite volume method. An irregular triangular grid is used to discretize the computational domain. As a result of the simulation, it is established that the type of the Saffman–Taylor instability, due to its randomness, strongly depends on the computational grid. After the production wells are flooded, the displacement front stabilizes. The instability increases as the ratio of dynamic viscosities of oil and water increases.
This study focuses on the analysis of an approach to the simulation of the phase transition in porous media when hot steam is injected into the oil reservoir. The reservoir is assumed to consist of a porous medium with homogeneous thermal properties. Its porous space is filled with a three-phase mixture of steam, water, and oil. The problem is considered in a non-stationary and non-isothermal formulation. Each phase is considered to be incompressible, with constant thermal properties, except for the dynamic viscosity of oil, which depends on the temperature. The 1D mathematical model of filtration, taking into account the phase transition, consists of continuity, Darcy, and energy equations. Steam injection and oil production in the model are conducted via vertical or horizontal wells. In the case of horizontal wells, the influence of gravity is also taken into account. The Lee model is used to simulate the phase transition between steam and water. The convective terms in the balance equations are calculated without accounting for artificial diffusion. Spatial discretization of the 1D domain is carried out using the finite volume method, and time discretization is implemented using the inverse (implicit) Euler scheme. The proposed model is analyzed in terms of the accuracy of the phase transition simulation for various sets of independent phases and combinations of continuity equations. In addition, we study the sensitivity of the model to the selected independent phases, to the time step and spatial mesh parameters, and to the intensity of the phase transition. The obtained results allow us to formulate recommendations for simulations of the phase transition using the Lee model.
This paper considers the artificial freezing of an argillite-like clay layer containing a NaCl salt solution in its pore space. The experimental results of the thermophysical properties of the clay with various salinities and water content in soil samples are presented. We determine the parameters of the soil freezing characteristic curves, the dependences of the specific heat capacity, and thermal conductivity based on temperature and salinity. These parameters are used in the formulation of a simple thermodynamic model for the artificial freezing of a clay layer with a single freezing pipe. The model includes diffusive transfer of heat and salt concentration, as well as salt precipitation when the eutectic point is reached. The motivation for using the simplified model is to understand the general patterns of soil freezing when considering the effect of salinity, as well as to test the proposed numerical finite-difference algorithm for solving the problem of freezing a clay layer based on the method of equivalent heat capacities. Using the algorithm, we analyzed the regularities of the redistribution of dissolved and precipitated salt in frozen soil, and also evaluated the effect of diffusive salt transfer on the numerical solution.