This research article investigates the particulate matter originated from the exhaust emissions of 20 bus models, within the territory of Vladivostok, Russian Federation. The majority of evaluated buses (17 out of 20) had emissions of large particles with sizes greater than 400 μm, which account for more than 80% of all measured particles. The analysis of the elemental composition showed that the exhaust emissions contained Al, Cd, Cu, Fe, Mg, Ni, Pb, and Zn, with the concentration of Zn prevailing in all samples by two to three orders of magnitude higher than the concentrations of the other elements.

Despite the fact that environmental pollution due to motorcycle exhaust gases reports a great increase, motorcycle production exhibits a great increase through the last years. Countries of Asia and Africa are reported to be the major regions where two-wheeled vehicles are a major transportation mode, with tens of millions of units sold per year. Motorcycle exhaust particles are considered to be the major contributor to environmental pollution due to their airborne dispersion, containing great amount of polycyclic aromatic hydrocarbons (PAHs). This study aims at reporting an objective analysis of the main sources of the ambient air pollution as also particle size distribution and chemical composition analysis of particulate matter originated from the exhausts of two-wheeled vehicles used in the territory of Vladivostok, Russia. Various types of two-wheeled vehicles were examined (motorcycles, ATVs, scooters and wet bikes) using different types of engine and fuel system. Experimental results showed that there was no clear relation to the particle size distribution with the engine displacement of motorcycle and the number of strokes and the fuel system. Instead, there were reported two clear assumptions. The first one is that regarding to the motorcycle brand, a few samples did not exhibit a great percentage of PM10 fraction. The second one is that more modern vehicles, that have a harmful gas afterburning system, are usually the source of an increased percentage of PM10 emitted particles. At last, it should be mentioned that the laser particle size analysis method is capable of determining the particle sizes after their agglomeration whereas the optical morphometry method allows to determine the real particle size of emissions. In conclusion, it can be pointed out that the agglomeration of particles can lead to the reduction in the toxicity of particles emissions originated from two wheeled-vehicles.

Arc welding operations are considered to be risky procedures by generating hazardous welding fume for human health. This study focuses on the key characteristics, as well as dispersion models, of welding fumes within a work zone. Commercial and widely used types of electrodes with various types of covering (rutile, basic, acidic and rutile-cellulose) were used in a series of experiments on arc welding operations, under 100 and 150 amps of electric current. According to the results of this study, maximum levels of pollution with particles of PM₁₀ fraction occur in the workspace during arc welding operations. Disregarding the types of electrodes used, the 3D models of dispersion of the РМ₁₀ particles at the floor plane exhibit corrugated morphologies while also demonstrate high concentrations of the РМ₁₀ particles at distances 0–3 m and 4–5 m from the emission source. The morphology of these particles is represented by solid and hollow spheres, ‘nucleus-shell’ structures, perforated spheres, sharp-edged plates, agglomerates of the tree-like (coral) shape. At last the bifractional mechanism of fume particle formation for this type of electrodes is also shown and described. In this article results are reported, which demonstrate the hazards of the arc welding process for human health. The results of the characterization of WFs reported improve our understanding of risks that these operations pose to human health and may strengthen the need for their control and mitigation.

A comprehensive analysis of the state of air inside an industrial workshop with electroplating production was carried out. The data of quantitative distribution of suspended particles by size fractions (PM_0.3, PM_0.5, PM₁, PM₃, PM₅, PM₁₀) are presented for 15 main processes of electroplating. Morphometric and chemical composition of the surface of particles were studied. We observed particles of rounded shape, various agglomerates with complex geometric shapes, acute-angular particles, which when inhaled pose a maximum threat to human health. Chemical analysis of these particles showed an absolute predominance of oxides of non-ferrous metals, the percentage of which varied depending on the type of electroplating bath. The content of highly hazardous substances of the 1st (Zn, Pb, and Cd) and the 2nd (Cu, Cr, Ni, Co, and Mo) hazard classes in each sample was recorded.